Jump to content
SAU Community

Recommended Posts

Hey everyone, I just finished fitting the GT2860-5's to my R32 gtr and must say they've made a huge difference, the car feels more responsive and comes on boost earlier too. On full throttle it's fine but on really light acceleration and at cruise I now get bad waste gate flutter and surging. I never had this problem with the original turbo's and haven't changed anything other than the turbo's and a bit of metal off the exhaust manifolds.

Any ideas?? Help please!!!

Link to comment
https://www.sau.com.au/forums/topic/160901-gt2860r-5s-surging-flutter/
Share on other sites

  • Replies 54
  • Created
  • Last Reply

Top Posters In This Topic

how much boost are you running? maybe you might need an aftermarket BOV.

Around 1bar I think (factory gauge). But I don't think it's got anything to do with the BOV's, It's barely seeing any boost at all at very light throttle.

I think his actually trying to describe the compressor surge problem.

I had this really bad on my GTR when I first bought it. with the original 2530's fitted it would "chuff" when cruising or light throttle up hill etc.

I bumped the base timing up by 2 degress and it fixed the problem.

it's compressor surge and the shuffling comes from the return pressure wave. after market BOV's being more heavily sprung will make it worse.

changes to tuning and/or cam gear positions should get rid of it.

edit/correction: it is not the BOV opening and closing, it is the flow of air back thru the AFM/airbox as incorrectly posted.

Edited by wolverine
Ok, I'll start with the basics i.e tune and see how it goes. I went through all the other threads on this topic and everyone is seems quick to point the finger at the BOV's.

its not the BOV's...to prove a point disconnect the vaccum line to them and block it so you don't have a manifold leak, then go for a light throttle drive up a long hill....i bet it still happens. Its the compressed air from the larger turbo's surging back out the intake through the AFM's.

You would not be on the throttle hard enough to generate boost, so the BOV would not even operate.

Ash ive had 2530's chuff so bad the car was almost undrivable....quick tune at Croydon's...magic...all gone!

Stock GTR BOV's are very good ive even seen them on hard tuned Supra's

Alright, well they are a fair bit bigger than the standards so I'm not ruling compressor surge out yet. I'll crimp the vacuum lines to the BOV's rendering them inactive tomoz and see what happens. But I don't understand how different turbo's is going to throw the BOV's out of wack??

Yer I've heard the standard BOV's are really good and I seriously doubt that they are the cause. But I shall test them and the plumbing for them anyway just so we know for sure. First i'll bump the timing up a tad as you suggested and see what happens. I've still only got a mines modified ecu at this stage so tuning is limited, wolf 3d coming soon. Thanks for the advice everyone, I'll let you know what I find.

i have been told this with my setup that the turbo was producing too much air forcing air through to my afm. causing more fuel and hesitation.

Apperantly only way to fix it (from what i have been told) is if ya get a computer that has an inbuilt map sensor, or move the afm to another location before the TPS.

Bit of farkin around but if thats what has to be done, then thats it.

Im upgrading turbo anyway so i'll deal with it when time comes.

Edited by bazr33

Yer that's why I'm going for the wolf 3d v5, do away with the afm's all together, bit more expensive but I think the plug n play is the way to go. But for now, unless a simple tweak of the CAS will fix it, it looks like I might just have to deal with it. Oh well, I was looking for another reason to spend more money on her!!

Well today I blocked off the BOV vacuum lines - made no difference what so ever - still very bad WASTEGATE flutter and surging goin on under there - rules out the BOV's once and for all (and it upset the idle). Advanced the CAS - made no difference either. It seems to occur right on the transition from vacuum to boost, near impossible to drive slow.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • Those above shitboxes, mediocre and above usually have a turbo strapped to them, hence the slightly higher octane is required.  
×
×
  • Create New...