Jump to content
SAU Community

Recommended Posts

i probably wouldn bother unless ur going for some psycho amount of power, i run 400rwkw with my rb26/30 with still room to push more and it hasnt been ported. id probs only bother just doing a slight little tidy up, but dont go all out

i probably wouldn bother unless ur going for some psycho amount of power, i run 400rwkw with my rb26/30 with still room to push more and it hasnt been ported. id probs only bother just doing a slight little tidy up, but dont go all out

It says at the bottom 496hp@21psi ?? sorry to say mayt but thats not 400rwkw its actually around 370rwkw.i know im off-topic but im just saying.

An alternative opinion, why not………..

RB heads (all of them) are NOT as good as some people would have believe, they have daggy castings, rough edges, unequal port dimensions, different sized combustion chambers etc etc.

Sure you can make lots of power without porting, but you have to run MORE boost to squeeze that airflow through the small ports.

MORE boost, that means MORE retarded ignition which means LESS response

MORE boost means SLOWER boost build, advancing the ignition will give FASTER boost build.

MORE boost means you need a bigger intercooler, to take that EXTRA heat (caused by the compressor working harder) out of the airflow produce by the compressor.

A SMALLER intercooler and pipework means FASTER throttle response

So after porting, you can make the SAME power at LOWER boost, with MORE response, FASTER boost build and QUICKER throttle response.

At the same time as he is porting it, a good machinist will equalise the combustion chamber volumes, so that the compression ratios on all 6 cylinders are exactly the same. Service the head, new valve stem seals, check the valves and guides, cut the valve seats, set the valve spring seat pressure etc etc. . All of which is essential for a reliable top end. Plus he will match port the inlet and exhaust manifolds, which on its own can make a huge difference

So why wouldn’t you port it? Cost, well it costs less than a mega intercooler and its pipework. Inconvenience, yep you have to give your cylinder head to someone for around a week, which is not that long in an engine build. Seems like a small price to pay considering the benefits.

:) cheers :D

On a side note I have some oversized valves for sale at the moment which would work very well with a head porting.

JHH seem very knowledgable to me, is there anyone in Sydney that can doa good job and turn around the work quickly and reliably???

On a side note I have some oversized valves for sale at the moment which would work very well with a head porting.

JHH seem very knowledgable to me, is there anyone in Sydney that can doa good job and turn around the work quickly and reliably???

Just got our head heavily ported, oversized valves, and matched. Croydons sent it to someone who does all the port work on their "big" engines (GTR-700, RH9, JUN, DEVLSH etc). BUT..... it was sent there well before Xmas and only got it back a couple of weeks ago.

My head was CNC ported, but i didnt pay for it. I had the head specialist at my job do it for me bribing him with beers and a BBQ. we have someone that studied at caltech for this sorta work, and at the workplace we have the cnc equipment and the dude that calculates evrything, so why not misuse that, its quite precision work with a buret and all that crapola measuring into the wee hours of the night. but its done perfectly and the results are great

interesting, i stand corrected then... from what a fair few ppl told me the cost/gain ratio wasnt worth it but ill look into it... so how much are we looking at here to get an rb26 head ported?

super dragger- as it says under my avatar that was previously using the rb25 head, stock rods, oil pump, and smaller fuel system, it has not been updated

ben...

Edited by 2BNVS
interesting, i stand corrected then... from what a fair few ppl told me the cost/gain ratio wasnt worth it but ill look into it... so how much are we looking at here to get an rb26 head ported?

ben...

Quoting prices on cylinder head jobs is not always that simple. You don’t know what parts are needed until you disassemble the head and check everything. For example, RB’s often have bent exhaust valves. Not always all 12 are bent and they are ~$30 each, so do you include $360 in the quote or not?

There are 2 philosophies;

1. Charge ~$2K which is enough to cover ALL the possibilities, if that particular head doesn’t need some parts then you do OK on that one. The next head might need everything and you don’t do so well on that one.

2. Charge ~$1,300 plus parts, if required. That’s a normal head service which includes valve grind, new Nissan seals and gaskets (VRS kit), machine all surfaces (inlet, exhaust & head face), check the camshaft tunnels for straightness, bore if necessary, set valve spring tension and set the tappet clearances (including shims if required). Plus porting, inlet and exhaust ports and combustion chamber volume matching. If they are supplied, the inlet and exhaust manifolds are match ported to the head.

It doesn’t include valve guides (if required), valve seats (if required) inlet valves (if required) or exhaust valves (if required). If you want aftermarket (oversized) valves, cams, springs, followers etc then you have to supply them with the head to be serviced.

Our race team cylinder head guy is not too busy at the moment, so we can sneak in a head or two. He has done over 50 RB cylinder heads, I reckon he he can do them in his sleep. PM me for details.

:nyaanyaa: cheers :ninja:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...