Jump to content
SAU Community

Recommended Posts

.86 rear housing, .60 front, made 250kw on low boost, virtually no lagg over stock turbo

Do you have graphs to back up this wild claim? 250kw, low boost, no lag :)

I am in the market for a turbo, so i do have a geniune interest.

before you put up an insult do some investigation yourself. check the link below, the lower rated 28/71r is rated at 390hp which equals about 285 kws.

who is talking bs now??????

http://www.horsepowerinabox.com/HPIAB2/turbochart.htm

great turbo upgrade for rb's. buyer will be happy. depending on sizings, it is the equivalent of the HKS GTRS

larger ARR and trim will be more suited to rb25

i run one in the smaller ARR and trim on my rb20 and made 230rwkws on 18psi with better response than the neo turbo i had on previous

Since item is sold, i'll reply:

before you put up an insult do some investigation yourself. check the link below, the lower rated 28/71r is rated at 390hp which equals about 285 kws.

who is talking bs now??????

http://www.horsepowerinabox.com/HPIAB2/turbochart.htm

Doing research is one thing, understanding it is another :( ; and unfortunately you have not understood the specs.

This turbo is rated at 440hp=310kw approx

This 310kw is at maximum flow at flywheel in ideal conditions without losses, etc. Consider losses in driveline, fuel inconsistancies, engine wear, etc and you'll probably have 250rwkw, but at maximum flow (max. boost), which is far higher than the 12psi claimed.

So try and understand what you read, before going off at people.

rb20inside: The Neo turbo is larger than the r33 rb25 turbo. So yes the Neo would be pretty damn laggy on a 20 :happy: 230rwkw at 18psi sounds about right for this turbo.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...