Jump to content
SAU Community

Recommended Posts

Acc Name: r3load_

Style: Drift

Track: Reverse

Car: Tuned Evo9

Score: 6153 (crap i know)

Global Rank: cant remember, im at work.

What kind of setup are you guys running with your cars?

mine is:

ASM: OFF

Traction Control: 8

FW: Racing 2's

RW: Sports 1's

Porbably not the best setup but its gets me the highest scores i got above.

can't remember my score, but i know i was rank pretty much 1st for both evos dont know if it change now i check later tonight

username kaido

Think you're going to have to have another crack at making #1 again coz you're no longer in the top 10. :P

PS: what's the deal with the advertisement for Yahoo Japan in your sig? :(

What kind of setup are you guys running with your cars?

ASM: OFF

Traction Control: 0 (Off)

FW: Racing 3s

RW: Racing 3s

You definitely need ASM & TC off for drift, it may feel a little hard at first but you'll need to get used to it. Also go into Rankings & watch the replays of the top scorers, it'll give you an idea of what lines to take & when to rip the handbrake up. :P

Personally I like to use the ‘front bar’ camera instead of behind the vehicle, when using the front bar camera it’s easier to notice how the car behaves & corners, also good for using sensitive movements with the analogue stick.

Also if you’re not using the hand brake you should be, I hand brake to start the drift into every corner so that I’m sliding sideway a little bit before I reach the corner then try to full throttle drift it all the way through & out, this is the trickiest bit trying to get the right line sideways on full throttle all the way through the corner.

More scores peoples!! :(

Yeah i did watch a few of the top scorers and im using TC: 0 now.

I pretty much use the same tactic as you except i seem to have to use the brake otherwise im gonna slide all the way into the opposite barrier.

i handbrake into the corner, then alternate throttle and brake in and out of the corner.

I dont get the rankings, do they reset or something?

Because you are no longer in the top 10 geno8r but there are cars with less than your 12169 drift score now in the top10..

At the moment im currently globally ranked 6th with only 11463 points for the tuned R32 reverse drift.

Edited by R3LOAD
  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...