Jump to content
SAU Community

Recommended Posts

well GGG are the softs, I would say SG are probably even softer, like maybe a wet compound, or motokhana compound. ie, desinged to come up to temp very quickly.

i wouldn't worry about it too much, but if you were buying again I'd say go the G or GG.

Page 3 of this PDF goes into a bit of detail about the compounds and suitability.

Looks like SG is the softest compound. Should be suitable for a few hot laps at a time. Not ideal for hot track temps or too many laps without cool down.

they would be ok, but no where near as good as drag radials as the sidewalls of the toyos (like all circuit biased semi slicks) is soo stiff it doesn't give that great launch you can get with the drag radials.

hmm.....

I havent used mine yet - I got the ones from St George tyres

But I guess for my sort of usage - i.e. 'kharna's and few track days - Im not that quick on the pace nor do I go "that" hard - Im confident they'll be perfect for my useage

but of course, I'll keep you all updated when I finally get them on for a session or 11ty :)

Hey Guys,

Just thought I would stick my head in and mention that the Tyres being sold from Taleb Tyres were not sourced through Toyo Tyre and Rubber Australia.

The following is an abstract taken from an official bulletin released from Toyo Tyre and Rubber Australia.

"Toyo Tyre & Rubber Australia Limited has been importing very small quantities of Proxes R888 with the "GGG" compound, in the 195/55R15 size only, for specific users through Toyo motor sport tyre dealers. "GGG" compound tyres have only been provided to users after the motor sport tyre dealer & Tyre Technical Department have identified the using conditions as being suitable for this tread compound."

"Retailers and wholesalers of parallel import Proxes R888 tyres are not specialist Toyo motor sport tyre dealers and are therefore unlikely to have the knowledge to advise Toyo motor sport tyre dealers and are therefore unlikely to have the knowledge to advise end users regarding the product that is best suited to their application. Most importantly,it is unlikely that end users purchasing parallel import Proxes R888 tyres know the tread compound of the tyres they are purchasing. "GGG" & "SG" tread compound tyres are suitable for a very narrow range of using conditions. It is unlikely that end users purchasing parallel import Proxes R888 tyres with "GGG" & "SG" tread compounds will have tyres that are suitable for their using conditions, and therefore are likely to be disappointed with the performance of these tyres."

Not saying don't buy them guys, but be careful >_<

Cheers,

Dan.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Dear folks My family members have 4 different cars : Triton 2015 and Corolla 2011 and Mazda3 2012 and Hyundai Elantra 2014 Looking to buy engine oil funnel spill free What I found are are below  https://www.amazon.com/gp/aw/d/B0BBTTJNKX?ref=ppx_pt2_mob_b_prod_image&th=1 https://www.ebay.com.au/itm/145553221359?srsltid=AfmBOoqYBU6Ptw0LU_bAp_k67U3qkF97HHvePkA7iHZw8vUmiwoIRaRr https://www.amazon.com/gp/product/B09X23TCS5?th=1 Is there a funnel with attachment that fits most cars ? Don't mind to spend for a decent quality  Thx  
    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
×
×
  • Create New...