Jump to content
SAU Community

Recommended Posts

Im looking for pic's of gauges custom mounted in to a r33 dash, im getting around 5 gauges 60mm in diameter. Im thinking of putting them above the glove box in a row. If any one has pic's or idea's where to place them it would be great.

Cheers

Dave

Link to comment
https://www.sau.com.au/forums/topic/164964-custom-mounted-gauges/
Share on other sites

Gauages everywhere (unless your a track racer) is a thing of the past... I think it looks rather lame to be honest... I got one Boost guage (high quality thta cost around $400.00) and that's it... one is enough... one looks tough... shows that you're all go and less show... if you have cross-rainbow colour gauages everywhere... to me, it looks like something from a cartoon... up to you though.... and yes, too many gauages will bring the cops onto you...

Im looking for pic's of gauges custom mounted in to a r33 dash, im getting around 5 gauges 60mm in diameter. Im thinking of putting them above the glove box in a row. If any one has pic's or idea's where to place them it would be great.

Cheers

Dave

6 gauges!!! what are they?

boost

oil temp

oil pressure

air/fuel

volt meter

coolant temp (they are all in white face)

shift light

iv only got the boost and oil pressure so far, i might just place them in a row above my glove box and im getting the ash tray mounted gauge pod soon. the engine is getting a hks rebuild so i wana read the engine a bit more, look after her

Edited by cruzin33

its alright if you line them up so when everything is working right, all the needles are straight up, all in the same direction...

then you can glance over and see if anything is wrong...

IF you need that many... :blink:

Edited by DRD-00F
ya im thinking of getting gauge pods made up to put them on a slight angle above the glove box and mould them in

then be prepared to replace your dash if you ever get defected .. that area is the crash zone .. needs to be padded

I suggest mounting them as close to your normal field of view when driving as possibe. That way you only have to take your eyes off the road for 1 second to check them, not turn your head etc.

These are mine - oil pres., oil temp and boost. The HC tells me everything else I need to know.

post-8870-1176971154.jpg

then be prepared to replace your dash if you ever get defected .. that area is the crash zone .. needs to be padded

In adelaide its a bit diffrent, we just cant have them above the dash

Edited by cruzin33
  • 3 years later...

It would have been easier to carbon or glass over the entire hole and cut some new holes to fit but I didn't want to do anything I couldn't undo easily.

Could have just bought another interior piece and done it though :(

Haha, one of those things you just dont think about...

Another idea, my mate drilled a slot into his dash (I know that makes no sense) and pushed his PFC controller into it, so its al eye level directly in front of his when he drifts. Another idea for you racers/drifters.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...