Jump to content
SAU Community

Recommended Posts

Hey all

im looking to paint my FMIC and the piping (if i have paint left over) black...

the thing is, my cooler is a bit damaged, so i was looking to replace it soonish, so i thought id give painting the current one black a go..

I remember a thread/debate on here saying which paint to use.. So i have a couple of other questions..

1. Which paint do i use?

2. Is it available in spray can or in a bucket?

3. Which will give better results (im thinking can)

4. Assuming i paint the cooler only, should i take the front bar + fmic off? Or front bar only and simply mask and paint the visible parts of the cooler?

5. Do i need to "sand" back the cooler or piping (which is shiny aluminium) ?

6. I just had a knee reconstruction a few months ago, so is it a one man job (fitting the cooler back on)?

7. Cheers :):P

Edited by DjeMz

just paint it matt black....no need to do anything but spray.....but i recommend taking it off the car....it will be easier in the long run.....piant the piping as well.....engine bay wont have a mirror in it....good for defects...

Core: i used a $2 matt black can and a light coating, piping you can get a better finish using a better paint... UHT heat paint for Brakes/enginge parts, if used correctly will look good when you open the bonnet....

there was a debate before on the heat reducing aspect to painting a cooler IE: the thicker the paint the less heat is extracted

Very, very light coat. Otherwise the paint will act as an insulator, keeping the heat in the aluminium and transferring it back into the intake charge. Ceramic coating would be as good as not having an intercooler at all.

and if i completely f**k it up? would ia high pressure squirt from the car wash be enough to take the paint off?

thats why a light coat of cheap paint is best, if you do f#$K it up it will come off with thinners / turps....

  • 4 months later...

In regards to painting the cooler, have had them powder coated in the past, and also seen them powder coated on some high powered cars.

Powder coating gets the best finish, and paint doesn't chip/fade anywhere as easy at cheap shit paint out of a can.

Anyone else had there's powder coated? I will be getting mine powder coated for a mint finish.

I know its an old thread, but me and DjeMz were talking about it and thinking of whats best, so thought I'd bump his old thread up.

Thanks,

Abu

Powder Coat only.

Take the pipes to a local Powder Coater, tell him you want "Satin Black".

He'll probably charge you minimum fee which is normally like $40.

Tell him you want to do do it for cash or beer and it will probably be ever cheaper.

100 times better and more durable than paint.

Powder Coat only.

Take the pipes to a local Powder Coater, tell him you want "Satin Black".

He'll probably charge you minimum fee which is normally like $40.

Tell him you want to do do it for cash or beer and it will probably be ever cheaper.

100 times better and more durable than paint.

Yeah thought so.

SATIN BLACK is the shit. :)

My uncle owns a powder coating factory, so best rates alll thee wayyy:thumbsup:

Edited by abu

i don't think you would want your core powder coated - maybe the pipes, but that stuff is a bit thick. much thicker than spray paint or anodizing that's for sure. powder coat is tough for a reason.

i had mine painted by a radiator shop for $20 bucks. Looks fine to me although it's a little bit glossier than i was expecting.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...