Jump to content
SAU Community

Recommended Posts

For a while now my 32 gtr has been carrying on a bit first thing in the morning. On light throttle it sort of misfires and I can hear the air going chew-chew-chew (while I've still got the power down). On more throttle I can hear this loud sucking noise, but it is way down on power.

But then as the temperature gauge gets to half way, it’s like a switch has been flicked and the car becomes totally normal, full power and full boost available. All good.

This is something that’s been getting gradually worse, but today (coldish day) the switch didn’t flick when it warmed up and it carried on like this for ages. Got out looked for loose hoses or anything like that, but all appeared normal. I turned it off, waited a minute, turned it on again and everything was sweet. WTF?

I’m thinking it might be a dodgy air flow meter screwing with the computer as it fixes itself so quickly. Does that sound right?

Things I can rule out:

- Turbos – because they are the best part of a week old and it was doing this before

- Oxygen sensors – brand new

- The plugs were recently checked out and gapped

Ps. Running stock computer

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

you really want to check the coolant temp sensor. this sensor is used for fuel enrichment when the engine is cold.

chances are its stuck at a hot value (resistance) and the car is running real lean when its cold.

can measure the resistance of the sensor with an ohm meter with it disconnected or use a volt meter with it connected to see if its in spec, but either way from your description this sounds the culprit.

Hey, I'll be interested in what you find is wrong. I have a 33 GTR with the exact problem. However i have not replaced the oxygen sensors. But i did check the coolant temp sensor last night, i got a reading of 2.4k ohms which is a little below the spec of 2.6k at 20 degrees.

Jazza.

Jazza,

not sure if I can add value to this issue, but I wouldn't expect the diference in resistance between 2.6k ohms standard vs 2.4K ohms measured will be an issue - that difference is within 10% - so I suspect you have another gremlin somewhere.

Typical electronics specs for resistors (non automotive) is +/- 10%. Automotive won't be very different.

Mike

The battey has been in the car since i have owned it (about 8 months) it sometimes sounds like it's lacking cranking power if havn't driven the car for a few days.

Whats interesting is if i rev the engine (below 3k) it has the missfire and chutter, then if i unplug the O2 sensors it revs freely. Makes me think there giving the ecu wrong readings.

I've checked alot of other things i thought it may have been like trying another good set of coils, changing igniter, changing plugs & gaps, cleaned air flow meters & check voltages, throttle voltage, fuel pressure, coolant temp sensor, timing, there are no ECU error codes are coming up. So it's got me pretty buggered at the moment.

Thanks for your help.

The fact that it ran OK after you stopped and re-started suggests the battery is on its way out. You don't know how old the battery was before you got the car, so it could well be the source of the problem.

If you are not prepared to replace the battery immediately, get hold of a mate's that you know is relatively new and see if that cures the problem.

Sorry, i wasn't that clear. The car only runs like crap when it's cold. When i unplug the O2 sensors while it's running like crap and rev it, it clears up and revs smoothly. That gives an indication of a faulty sensor or incorrect reading maybe.

It runs fine when it warms up, and like the post above, it's almost like a switch gets flicked because the car goes from running very poorly, e.g. hesitating and chattering out the air filters to absolutely fine and normal in half a second.

Thanks for you help, i will replace the battery soon to something with more grunt.

Yeah well as I said in my original post my o2 sensors are brand new as they were changed with the turbo/dumps a week ago - so rules them out in my case.

I'm going to see how much a new coolant temperature sensor is tomorrow, and also see about my air flow meters. I have heaps of oil and crap in my intake pipes (bigger issue) so that's why I suspect afms.

I'll keep you posted.

I have a sim Issue but it happens sometimes even when the car is warm going to take it to hyperdrive tomorrow let you know what they think and maybe it might give you a direction

any updates on price of coolant sensor?

Yeah rang up today about the coolant sensor. The guy sounded a little confused... he concluded there is a sensor right near where the top radiator hose goes into the block that sends messages to the computer. It's $93.40 retail price and the part number is 2263001U00 (if I can read my shite hand writing correctly).

I'm going to hold off on it until I can rule out my afms. I cleaned them today with electrical spray, but obviously can't see if it's made any difference until the morning when it's fully cold. I'll let you know.

The AFMs wont be the culprit because the cold issues disappear instantly every time once the temperature reaches a certain level. (like flicking the light switch on) Ive got the same thing when i run my standard computer. When i run a non-tuned PFC, then the problem isnt there.

I reckon rb30-POWER is onto the problem...it has to be temperature related

Well this morning, after cleaning the afms and resetting the computer - it didn't do it!

But I'm not going to claim victory yet - I bet the twisted bastard of a car is just playing games.

So yeah anyway RB30, that would be tops if you could give us a run down on testing the coolant temp sensor. Firstly, where is it? I'm told it's near the top radiator hose - but there seems to be a few different sensor looking things around there.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Maf is a question mark but TPS  I have set at 0.47, the fact that I’m getting proper voltage range out of it with the key on leads me to believe it’s functioning properly. I’m getting proper voltages on basically everything. I still need to look up voltage ranges for z32 maf and test that 
    • Honestly no not at all, but it’s a very basic tune, it’s stock injectors q45 tps and z32 maf. Other than that it’s a completely stock base map. The file is from nistune and from my understanding if it was tune related I would be able to unplug maf and tps and it would still start even if it was a really shitty start. I have tried starting it with coolant temp, maf, and tps unplugged none of those 3 togethor or individually changes anything 
    • 🏆 Skyline Supremacy Meets Mount Panorama Magic 🏆 Join SAU NSW as we take the long way to Bathurst, the home of GTR greatness. Saturday 30th August 2025 7:00AM Meeting Hanna Park North Richmond 7:30AM Departure Cruise Via Bells of Line Road 9:00AM Arrival to Stop 1: Golden Poplars Meadow Flat 9:45AM Arrival to Final Destination: Mount Panorama Motor Racing Circuit Meet Location: Hanna Park North Richmond Stop 1: Golden Poplars Meadow Flat Final Destination: Mount Panorama Motor Racing Circuit   *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • What does it look like with highway driving? And yes, I had a similar thought as Duncan. It looks quite similar in my Stagea and I have made myself accept it as normal. Might have to look into it some day   Highway gets as low as 10l/100km on my end so I'm not as worried about it being a mechanical issue. More likely just the tune on the haltech.
    • While I was waiting for the new parts to come in for the charge pipe and radiator I decided to do some turbo modification. The drive pressure (exhaust backpressure) was a lot higher that I thought it should be. For 32lbs of boost drive was 55lbs. The turbine housing is a 1.10AR and my turbo builder has suggested to go to a 1.25AR. To test if a larger AR would do anything to reduce drive pressure AND not spend any money I decided to hog out the divider in my current housing. I removed it from the inlet and the whole way through the housing.  After reassembly and testing it doesn't look like this modification did anything for reducing drive pressure or requiring more fuel (making more power). Oh well, it was worth a shot. We'll get some data at the track if it makes it past the 60ft. I also machined a $7 shift knob off Amazon to fit my Stillway shifter since I didn't like the Stillway shift knob. Next on the list was the radiator replacement and fabrication of a new intercooler tube that had no silicon coupler. No pictures of this - I was short on time each night after work to get this done and didn't stop to take pictures.  Next was to get the clutch disks out and replaced. Previously when installing the dogbox I had ordered a set of the same sintered iron disks I had been running because I switched to the 26-spline input shaft. I thought it was odd that they didn't have any markings or brand name on them like all my old disks had but installed them anyway. At the track I could not get the clutch to lock up using my normal strategies. After two track nights I reached out to the clutch manufacturer and ask their thoughts. They said they had to switch the material out because they were having trouble getting the original material and that this new material would not take to being slipped very well.  So out with the first set of 26-spline disks and in with the correct material 26-spline disks. While I had the trans out I added an inspection/service hole. I've wanted one of these for a while. Now I can have a look at things and change the front cover shimming when needed (clutch wear). I hustled and got the clutch change done in a few hours on a Saturday. Hopped in the car and drove home. On the way home I did a 1-3 pull. When shifting from 2nd to 3rd the core plug in the back of the cylinder head popped out and dumped all the coolant. Thankfully I was only 30 seconds from home and coasted it there. Datalog showed nothing unusual and 2.5psi of coolant pressure. That plug has been in there since 1992 but I guess it worked its way out. Pulled the trans AGAIN and replaced the plug, JB welded it in, and made a brace. Also deleted the head drain I had added in during the bearing issue fiasco.  I am currently changing my boost control plumbing to make it cleaner. After that is done I'll make another attempt at getting past the 60.
×
×
  • Create New...