Jump to content
SAU Community

Recommended Posts

the fine is $10000 for u and $40000 for the wprkshop that did it. or something like that

What part of max fine don't you understand.

I received 1 point and $75 and had to take my car to the Police once I had the exhaust fixed to clear it.

I ended up just de registering the car as it was sold anyway and paid the fine :)

  • Replies 78
  • Created
  • Last Reply

Top Posters In This Topic

and yes, i'm having screamers and no cat's :)

Your my hero shane :)

If you want have a screamer that the average grunt wont be able to spot get the outlet extended to run along your exhaust so it looks like it comes back plumbed in. That will confuse most piggys however noise pollution fines will still come!

If you want places, any custom exhaust place will do them for you. CES is one, but its better just to get a split dump that is plumbed in n e way, as there is no real perfomance gain out of them, and atleast it solves all legality reasons, if you want noise get the right exhaust and the right material for the exhaust if you want more noise get stainless intake pipe and apexi pod that way you can be happy

Good luck

Oh please get them shane :) VOTE 1 dob shane in for undue noise :) j/k

If you want places, any custom exhaust place will do them for you. CES is one, but its better just to get a split dump that is plumbed in n e way, as there is no real perfomance gain out of them, and atleast it solves all legality reasons, if you want noise get the right exhaust and the right material for the exhaust if you want more noise get stainless intake pipe and apexi pod that way you can be happy

Good luck

Oh please get them shane :) VOTE 1 dob shane in for undue noise :) j/k

there will be flanges and removable section to make it legal my dear boy ;)

oh and Vote 1 dob adam in for bald tyres and pollution with his excessive overfueling! :P

What part of max fine don't you understand.

I received 1 point and $75 and had to take my car to the Police once I had the exhaust fixed to clear it.

I ended up just de registering the car as it was sold anyway and paid the fine >_<

did u get fined by the cops or was it the epa. if the epa go over ur car u will find that i might be right

does any1 know where to get the already made 1s?. just jap was meant to be getting them over 6 weeks ago but doesnt look like there coming.

i cant send pms now for some reason. i write it out and push send and it doesnt com up in my sent items and never get replies back so id say they dont work. may just be this computer

improve gas flow

I mean to ask why does he need one... What makes him think it will help...

As an external venting wastegate pipe from a stock turbo will not seal properly from the main dump...

It will affect the back pressure on the turbine and hence cause it to take longer to spool. So infact it will not improve his situation...

Also its highlly illegal...

I mean to ask why does he need one... What makes him think it will help...

As an external venting wastegate pipe from a stock turbo will not seal properly from the main dump...

It will affect the back pressure on the turbine and hence cause it to take longer to spool. So infact it will not improve his situation...

Also its highlly illegal...

shuddup fool and let the man have his fun ;)

maximum of $10,000.

same as having a gutted cat.

emissions, flames, noise pollution...

ah crap. even before the engine build i had a no cat, flames & well over the legal db limit. I really wanted a screamer but i guess the amount of defects my car will have i really dont need the extra attention. I know sau doesnt support defective cars but i know i'm not alone on this situation

does any1 know where to get the already made 1s?. just jap was meant to be getting them over 6 weeks ago but doesnt look like there coming.

i cant send pms now for some reason. i write it out and push send and it doesnt com up in my sent items and never get replies back so id say they dont work. may just be this computer

Import Auto Parts. i believe sells split dumps he might have have screamers available..dont know.

Yes IAP or Banzai Parts Garage or if all else fails ebays your good friend....or maybe look at classifieds on this website. They pop up quite a bit. Expect to pay around $250 plus!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...