Jump to content
SAU Community

Recommended Posts

If you can find your paint code which should be on the ID plate on the fire wall, take it to somewhere like Autobarn and they can mix it up and put it into a spray pack can

It will not be 2 pak like your car and you will need to put clear over it aswell.

Link to comment
https://www.sau.com.au/forums/topic/165932-paint/#findComment-3073077
Share on other sites

Recently a nasty wheelie bin attacked my RVM. I got another one from Darrin, its silver and I want to paint it dark green.

Where do you get a spray can of Stagea colours? Any Ideas?

Hugh, I'm prettty sure mine and yours are the same colour (dark green - "Sherwood Green Pearl") - the paint code is DR-2.

:closedeyes:

Link to comment
https://www.sau.com.au/forums/topic/165932-paint/#findComment-3073398
Share on other sites

Actually Hugh, Lots of good autopaint shops have the facility to be able to put any paint they make up into a spray can. Just check around your area. Find a really good guy who'll not only use the formula but also be able to eye match the colour. The pearls do have a different base usually but a good painter will give you the drum on the best way to match it. Don't go down to the 16 yo shop assistant and expect them to able to do it. (maybe some could). As you know age defintely gives you more experience!! Or at least it SHOULD!!

Cheers John

Link to comment
https://www.sau.com.au/forums/topic/165932-paint/#findComment-3089408
Share on other sites

Actually Hugh, Lots of good autopaint shops have the facility to be able to put any paint they make up into a spray can. Just check around your area. Find a really good guy who'll not only use the formula but also be able to eye match the colour. The pearls do have a different base usually but a good painter will give you the drum on the best way to match it. Don't go down to the 16 yo shop assistant and expect them to able to do it. (maybe some could). As you know age defintely gives you more experience!! Or at least it SHOULD!!

Cheers John

Well I'm the 66yo, so I should know. Will be trying it out this week end, but only on the RVM. If the match is AOK, I'll repaint the rear bar I got from Rob.

Link to comment
https://www.sau.com.au/forums/topic/165932-paint/#findComment-3091574
Share on other sites

lol

open Windows

press Start button (bottom left hand corner)

press All Programs (just above the Start once you've pressed it)

press Accessories

then press Paint

voila, done.

:)

I've now got a Nipple Pink RVM. Still, spose it will be AOK for the Suckers.LOL

Link to comment
https://www.sau.com.au/forums/topic/165932-paint/#findComment-3092262
Share on other sites

I've now got a Nipple Pink RVM. Still, spose it will be AOK for the Suckers.LOL

Hey Hugh

Did you find any rust under the mirror?

When I removed mine to give them to you, I found a nice big hole under the left mirror, but it could not be seen when the mirror was fitted.

Link to comment
https://www.sau.com.au/forums/topic/165932-paint/#findComment-3092505
Share on other sites

Hey Hugh

Did you find any rust under the mirror?

When I removed mine to give them to you, I found a nice big hole under the left mirror, but it could not be seen when the mirror was fitted.

Yep. Not a lot though. The rust was not in/on the door skin, but seems confined to the pressed metal mirror mounting plate. Which seems to only have a single electrostatic coat of black paint.

Treated it with some Wattyl Killrust. Now I know how to get to it I will do the drivers side.

Getting the trim off was like ateenagers first. You know how to do it but it is a lot of fiddling about to get it in, err OFF.

Link to comment
https://www.sau.com.au/forums/topic/165932-paint/#findComment-3095562
Share on other sites

Yep. Not a lot though. The rust was not in/on the door skin, but seems confined to the pressed metal mirror mounting plate. Which seems to only have a single electrostatic coat of black paint.

Treated it with some Wattyl Killrust. Now I know how to get to it I will do the drivers side.

Getting the trim off was like ateenagers first. You know how to do it but it is a lot of fiddling about to get it in, err OFF.

Don't s'pose you would like to share the procedure? I would like to do some preventative maint/explorative myself & would be interested in the "howto" before I go ahead & stuff something up. Old age & cunning & all that..........pre-treated mirror backing plate sounds good.

Cheers GW :P

Link to comment
https://www.sau.com.au/forums/topic/165932-paint/#findComment-3099079
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...