Jump to content
SAU Community

260rs Ecu Plug

tRUkbOY

By tRUkbOY,
in Four Door Family & Wagoneers

 Share

Recommended Posts

stasis Mentor

stasis

Posted
Posted (edited)

As far as i know R32/33 GTR are the same and same for the 260rs. I got a R33GTR ECU and it fit perfectly onto 260rs. Atleast thats wat my tuner says

SDU shpuld have more info on this. Aks Simon. He should know

Edited by stasis
Link to comment
https://www.sau.com.au/forums/topic/165998-260rs-ecu-plug/#findComment-3074052
Share on other sites
260tech Proficient

260tech

Posted
Posted
As far as I know R32 & R33 GTR Engine ECU plugs are the same..............not sure about R34. What I want to find out is whether the 260RS ECU plug is the same as R32/R33 GTR or is it R34 GTR? Or are they all the same?

Hi there, just came across this query, lookin for something else as usual but with reference to my most venerable Apexi Auto (Turbo) Timer application guide in english, the following details are listed.

1. Nissan Stagea 260RS Autech version plug type = N4-a

2. Skyline R32 RB20DE throo RB26DETT ('91.8~93.7) plug type = N4-a

3. Skyline R33 RB25DET throo RB26DETT ('95.1~98.4) plug type = N4-a

4. Skyline R34 RB26DETT ('99.1~02.8) plug type = N4-a

5. Skyline R34 RB25DET ('98.5~01.5) plug type = N4-a

Dunno if this helps but there it is. There are other models listed outside these ranges if you have a specific model enquiry.

Cheers GW :(

Link to comment
https://www.sau.com.au/forums/topic/165998-260rs-ecu-plug/#findComment-3080421
Share on other sites
Chris Rogers Grand Master

Chris Rogers

Posted
Posted

one thing I did find (this is not a for a Rb26 though) R33 and C34 will pinout correctly for a PFC but the ECU A/C signal will not be sent out if you do the ECU swap using a PFC for a R33 into a C34. this is part of the reason Ska has a switch on the dash of his. the switch engages the A/C compressor instead of the ECU. everything else pins out and works.

Link to comment
https://www.sau.com.au/forums/topic/165998-260rs-ecu-plug/#findComment-3082158
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Dose Pipe Sutututu · Posted

      Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • Kinkstaah
      Strange issue RB25DET wont start

      By Kinkstaah · Posted

      I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • Kinkstaah
      First time Skyline owner

      By Kinkstaah · Posted

      The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • Kinkstaah
      Chris' Toyota Mark ii JZX110

      By Kinkstaah · Posted

      I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • GTSBoy
      Chris' Toyota Mark ii JZX110

      By GTSBoy · Posted

      I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...