Jump to content
SAU Community

Recommended Posts

Ladies and Gentlemen,

The time has come to part with my much loved 1990 Toyota Celsior F package.

I don't get to drive it anymore and have a new work ute to take it's place as a daily driver. I jumped in it the other day to get a roady and new tyres and still can't believe how comfortable it is and how nice it is to drive.

This car was the pick of the lot in Japan as the laws were changing and I just had to have it, if I was able to maintain 3 road registered cars I would keep it, but ...... Oh who am I kidding... My missus says I have to get rid of a car and I can't sell my Skyline...

Here are some pics, and the leather is sweet for a 16 yo car... oh yeah and the girls love the vibrating rear seats too.....

Really, they do.

It also has a fully sik V8 and so many electric thingos inside it that the mind boggles, well mine does anyway.

Vic rego expires in October, has current roadworthy, new Hankook Silica's.... Buy me. Do it.

post-3624-1177667807.jpg

post-3624-1177667962.jpg

post-3624-1177668108.jpg

post-3624-1177668278.jpg

post-3624-1177668542.jpg

Link to comment
https://www.sau.com.au/forums/topic/166328-toyota-celsior-sold-for-10000/
Share on other sites

  • 3 weeks later...

Server upgrade.

Danny... hurry with the pics yo... i dont think ive seen your Celsior.

Dunno if i could trust you tho... how many times have you been naked in the back of it with baby oil and midgets? Has it wrecked the leather?

Here are some pics again, and yeah, server relocation usually results in loss of images, dammit!

Nark... :happy: you know i always use protection, tarps and sponges, make sure folks clean their feet before they get in......

I will post more pics again to bump legitimately, I hope this car goes to a good home.

it is also advertised on carsales.com.au just search rego UCF011 (yes the number plate is the chassis designation, i am a tosser).

:)

post-3624-1179822824_thumb.jpg

post-3624-1179822961_thumb.jpg

post-3624-1179823165_thumb.jpg

post-3624-1179823387_thumb.jpg

I have the australian delivered LS400 - and it shits over any skyline for daily driving, where you are usually stuck in traffic anyhow. The only think that would come close is a car a couple of years old.

Returns about 11L/100km as well on the highway.. recommended :ermm:

  • 3 weeks later...
I have the australian delivered LS400 - and it shits over any skyline for daily driving, where you are usually stuck in traffic anyhow. The only think that would come close is a car a couple of years old.

Returns about 11L/100km as well on the highway.. recommended :wub:

Thanks Predator,

Looks like you've had some work done if that's you in your avatar....... wanna go for a beer :)

Of course you're all wondering if this fine example of a luxury motor vehicle is still for sale... well yes it is.

:)

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Should be more than fine, especially the overall fuel pressure would never exceed 3.5bar (assuming that thing never gets more than 0.5bar of boost in stock form). According to the chart, it's 11amps.
    • I definitely know the first rule here, look first, ask second. I've seen many people get roasted 😂 I found a few diagrams for the RB, but I'm yet to come across one for the VQ. From what I have read, the pump gets the +12v along with the FPCM, and it's the negative wire that gets passed through the resistor to regulate the voltage. So I assume I can just ground the negative wire at the pump to eliminate the FPCM control. But I really wanted to see the VQ circuit diagram first to make sure I understood it correctly. Once the new pump is in I'll do some testing to see how it behaves, and in the meantime, I'll keep looking for a wiring diagram. Thanks for your help mate, your time is greatly appreciated.    
    • Maybe? I have the Supercheap ToolPro low thingo. It has a somewhat smaller diameter lifting "bowl" than you would expect on a workshop grade trolley jack, and a split rubber pad to suit that diameter. It clears the "N1" style skirts I have. Probably wouldn't if the jack's bowl and a suitably larger rubber block were in use. Having said that though.....you only need the rubber block to exist on the inner side of the pinchweld, so could carve away any rubber that fouled the skirt, leaving some there for "insurance" </simples>
    • I used to do that (sills with rubber jack block).. ... then I got side skirts, and there's no way for the jack to actually work there, the jack pad itself on the jack is too big. Is the answer to use a... smaller (?) jack? Hmmm.
    • I have too much trauma from every skyline I've ever seen having crushed jack points/pinch welds lol.    Yep, works 100%, it's what I use when I'm using the quick jack. Don't know why I can't also bring myself to do the same thing when I'm using a jack. I blame the skyline PTSD. 
×
×
  • Create New...