Jump to content
SAU Community

Toyota Celsior Sold For $10,000

AutoTrust
 Share

Recommended Posts

AutoTrust Mentor

AutoTrust

Posted
Posted

Ladies and Gentlemen,

The time has come to part with my much loved 1990 Toyota Celsior F package.

I don't get to drive it anymore and have a new work ute to take it's place as a daily driver. I jumped in it the other day to get a roady and new tyres and still can't believe how comfortable it is and how nice it is to drive.

This car was the pick of the lot in Japan as the laws were changing and I just had to have it, if I was able to maintain 3 road registered cars I would keep it, but ...... Oh who am I kidding... My missus says I have to get rid of a car and I can't sell my Skyline...

Here are some pics, and the leather is sweet for a 16 yo car... oh yeah and the girls love the vibrating rear seats too.....

Really, they do.

It also has a fully sik V8 and so many electric thingos inside it that the mind boggles, well mine does anyway.

Vic rego expires in October, has current roadworthy, new Hankook Silica's.... Buy me. Do it.

post-3624-1177667807.jpg

post-3624-1177667962.jpg

post-3624-1177668108.jpg

post-3624-1177668278.jpg

post-3624-1177668542.jpg

Link to comment
https://www.sau.com.au/forums/topic/166328-toyota-celsior-sold-for-10000/
Share on other sites
  • 3 weeks later...
inark Grand Master

inark

Posted
Posted

Server upgrade.

Danny... hurry with the pics yo... i dont think ive seen your Celsior.

Dunno if i could trust you tho... how many times have you been naked in the back of it with baby oil and midgets? Has it wrecked the leather?

AutoTrust Mentor

AutoTrust

Posted
  • Author
Posted

Here are some pics again, and yeah, server relocation usually results in loss of images, dammit!

Nark... :happy: you know i always use protection, tarps and sponges, make sure folks clean their feet before they get in......

I will post more pics again to bump legitimately, I hope this car goes to a good home.

it is also advertised on carsales.com.au just search rego UCF011 (yes the number plate is the chassis designation, i am a tosser).

:)

post-3624-1179822824_thumb.jpg

post-3624-1179822961_thumb.jpg

post-3624-1179823165_thumb.jpg

post-3624-1179823387_thumb.jpg

predator Grand Master

predator

Posted
Posted

I have the australian delivered LS400 - and it shits over any skyline for daily driving, where you are usually stuck in traffic anyhow. The only think that would come close is a car a couple of years old.

Returns about 11L/100km as well on the highway.. recommended :ermm:

  • 3 weeks later...
AutoTrust Mentor

AutoTrust

Posted
  • Author
Posted
I have the australian delivered LS400 - and it shits over any skyline for daily driving, where you are usually stuck in traffic anyhow. The only think that would come close is a car a couple of years old.

Returns about 11L/100km as well on the highway.. recommended :wub:

Thanks Predator,

Looks like you've had some work done if that's you in your avatar....... wanna go for a beer :)

Of course you're all wondering if this fine example of a luxury motor vehicle is still for sale... well yes it is.

:)

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSP male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSP reducing bush?
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...