Jump to content
SAU Community

Recommended Posts

After writing off my first R33 (lesson learned, I won't do it again, promise!), I'm looking at another... I tried other cars but just keep coming back to the R33 :)

Anyhow. Have driven a few and some had the stock exhaust, I really liked the sound of it, so quiet.

I'm just wondering if I bought one and decided to keep the stock exhaust, what mods are worth doing? I've still got a powerfc from my old car, but I'm just wondering whether there will be much gains to be had in having it tuned? With say, an R34 SMIC and 10-12psi.

Or maybe there is a more free-flowing alternative available which doesn't add noise?

Sorry if this has been covered before, I searched for "stock exhaust" and didn't turn much up.

Cheers!

Link to comment
https://www.sau.com.au/forums/topic/167583-stock-exhaust-performance-gains/
Share on other sites

Yeah, I actually think the stock system sounds really good too. But if power is what you want it has to go, as far as noise goes you don't have that much of choice because aftermarket manufactures obviously design them to be louder for that sportier sound and better flow. What you could do is buy a decent 3" system off greenline.jp and add another resonator to reduce noise.

Edited by BAMR33
After writing off my first R33 (lesson learned, I won't do it again, promise!), I'm looking at another... I tried other cars but just keep coming back to the R33 :)

Anyhow. Have driven a few and some had the stock exhaust, I really liked the sound of it, so quiet.

I'm just wondering if I bought one and decided to keep the stock exhaust, what mods are worth doing? I've still got a powerfc from my old car, but I'm just wondering whether there will be much gains to be had in having it tuned? With say, an R34 SMIC and 10-12psi.

Or maybe there is a more free-flowing alternative available which doesn't add noise?

Sorry if this has been covered before, I searched for "stock exhaust" and didn't turn much up.

Cheers!

change the front/dump, and put a bigger cat - i think that would be a good start. I got the front/dump, large cat and the trust pe2 cat back...good performance gain, very quiet too. dynoed at 164rwkws at re customs.

get a front mount - just jap (for around 400), second hand apexi power fc ecu, tweek turbo to around 11psi - get a full tune. not sure what the power rating will be like though.....

someone can correct me if im wrong with those mods......(probably dont need the power fc - but most people have it)

i discovered a quiet exhaust is a pretty large restriction

i went from a stocko, to a blitz jobby with an extra muffler

was quiet as (missus request) but robbed me of a fair bit of power (around 30rwkw)

im running a 3" straight dump pipe, hi flow cat, and jasma approved cat back exhaust, its like 92dB on back off and 90dB on ramp up, has also a mid muffler and i had my sky tined last week at 168rwkw. only other mods are fmic, k&n panel filter and grounded out boost solenoid at 8psi. runs well enough.

guy i got the exhaust off said he had it tuned on his car and with it was still making 198 at the rears. IMHO, epa should go get fuc*ked. leave us to modify how we like as long as our pollution emissions are fine and the mods are rw. who cares if its a lil loud. ecu, pod, fmic, boost, wats it got to do with em. bloody poofters.

im running a 3" straight dump pipe, hi flow cat, and jasma approved cat back exhaust, its like 92dB

good for you, but your opinion is irrelevant here. 92dB is a long way from being quiet, in fact 84dB is the cutoff for continuous exposure without hearing damage. if you want to beat your chest about having a loud exhaust find somewhere more suitable.

  • 2 weeks later...
Fujitsubo make excellent exhausts for what you are after. They are quiet at idle and at cruise and have a decent sound when on full song.

My old R33 ran a Super Ti from memory, was great.

Thanks I will look into that.

I'm going to see if I can get the exhaust off my wreck and repair it. The front pipe and cat looked fine, but the catback was dented and the muffler a bit squashed... don't know how much it's going to cost me. Might have to replace the muffler altogether?

Is there much point just putting split dump/front pipe + hiflow cat on? Might free it up a bit without being noisier.

good for you, but your opinion is irrelevant here. 92dB is a long way from being quiet, in fact 84dB is the cutoff for continuous exposure without hearing damage. if you want to beat your chest about having a loud exhaust find somewhere more suitable.

Any idea how many dB a stock exhaust system would be?

Edited by bombastic
  • 2 weeks later...
good for you, but your opinion is irrelevant here. 92dB is a long way from being quiet, in fact 84dB is the cutoff for continuous exposure without hearing damage. if you want to beat your chest about having a loud exhaust find somewhere more suitable.

I think you're confusing something here - 92dB would be OUTSIDE the car, probably measured near the exhaust?

For a free-flowing exhaust thats still fairly quiet (sometimes inaudible when cruising at 50-60), make sure you get 2 mufflers, no resonators or anything. I've got a 3" oval magnaflow muffler at the rear and another 3" oval muffler in the middle. Being a wagon I need it quiet to reduce drone!

Its definitely quiet enough but not as quiet as stock.

To make it quieter and still get good flow, use twin pipes...although this will cost more.

It seems you either get good power, or a whisper quiet exhaust, but not both. Also I wouldn't bother doing other mods when you have the stock exhaust, except maybe just an SAFC or something - to maybe save a bit on fuel? Other than that, be aware that adding more boost pressure (ie. more psi) will likely just put more stress on your turbo without actually flowing more air through your engine (it could actually flow less!). psi is a measure of pressure, not necessarily airflow. :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...