Jump to content
SAU Community

Recommended Posts

After writing off my first R33 (lesson learned, I won't do it again, promise!), I'm looking at another... I tried other cars but just keep coming back to the R33 :)

Anyhow. Have driven a few and some had the stock exhaust, I really liked the sound of it, so quiet.

I'm just wondering if I bought one and decided to keep the stock exhaust, what mods are worth doing? I've still got a powerfc from my old car, but I'm just wondering whether there will be much gains to be had in having it tuned? With say, an R34 SMIC and 10-12psi.

Or maybe there is a more free-flowing alternative available which doesn't add noise?

Sorry if this has been covered before, I searched for "stock exhaust" and didn't turn much up.

Cheers!

Link to comment
https://www.sau.com.au/forums/topic/167583-stock-exhaust-performance-gains/
Share on other sites

Yeah, I actually think the stock system sounds really good too. But if power is what you want it has to go, as far as noise goes you don't have that much of choice because aftermarket manufactures obviously design them to be louder for that sportier sound and better flow. What you could do is buy a decent 3" system off greenline.jp and add another resonator to reduce noise.

Edited by BAMR33
After writing off my first R33 (lesson learned, I won't do it again, promise!), I'm looking at another... I tried other cars but just keep coming back to the R33 :)

Anyhow. Have driven a few and some had the stock exhaust, I really liked the sound of it, so quiet.

I'm just wondering if I bought one and decided to keep the stock exhaust, what mods are worth doing? I've still got a powerfc from my old car, but I'm just wondering whether there will be much gains to be had in having it tuned? With say, an R34 SMIC and 10-12psi.

Or maybe there is a more free-flowing alternative available which doesn't add noise?

Sorry if this has been covered before, I searched for "stock exhaust" and didn't turn much up.

Cheers!

change the front/dump, and put a bigger cat - i think that would be a good start. I got the front/dump, large cat and the trust pe2 cat back...good performance gain, very quiet too. dynoed at 164rwkws at re customs.

get a front mount - just jap (for around 400), second hand apexi power fc ecu, tweek turbo to around 11psi - get a full tune. not sure what the power rating will be like though.....

someone can correct me if im wrong with those mods......(probably dont need the power fc - but most people have it)

i discovered a quiet exhaust is a pretty large restriction

i went from a stocko, to a blitz jobby with an extra muffler

was quiet as (missus request) but robbed me of a fair bit of power (around 30rwkw)

im running a 3" straight dump pipe, hi flow cat, and jasma approved cat back exhaust, its like 92dB on back off and 90dB on ramp up, has also a mid muffler and i had my sky tined last week at 168rwkw. only other mods are fmic, k&n panel filter and grounded out boost solenoid at 8psi. runs well enough.

guy i got the exhaust off said he had it tuned on his car and with it was still making 198 at the rears. IMHO, epa should go get fuc*ked. leave us to modify how we like as long as our pollution emissions are fine and the mods are rw. who cares if its a lil loud. ecu, pod, fmic, boost, wats it got to do with em. bloody poofters.

im running a 3" straight dump pipe, hi flow cat, and jasma approved cat back exhaust, its like 92dB

good for you, but your opinion is irrelevant here. 92dB is a long way from being quiet, in fact 84dB is the cutoff for continuous exposure without hearing damage. if you want to beat your chest about having a loud exhaust find somewhere more suitable.

  • 2 weeks later...
Fujitsubo make excellent exhausts for what you are after. They are quiet at idle and at cruise and have a decent sound when on full song.

My old R33 ran a Super Ti from memory, was great.

Thanks I will look into that.

I'm going to see if I can get the exhaust off my wreck and repair it. The front pipe and cat looked fine, but the catback was dented and the muffler a bit squashed... don't know how much it's going to cost me. Might have to replace the muffler altogether?

Is there much point just putting split dump/front pipe + hiflow cat on? Might free it up a bit without being noisier.

good for you, but your opinion is irrelevant here. 92dB is a long way from being quiet, in fact 84dB is the cutoff for continuous exposure without hearing damage. if you want to beat your chest about having a loud exhaust find somewhere more suitable.

Any idea how many dB a stock exhaust system would be?

Edited by bombastic
  • 2 weeks later...
good for you, but your opinion is irrelevant here. 92dB is a long way from being quiet, in fact 84dB is the cutoff for continuous exposure without hearing damage. if you want to beat your chest about having a loud exhaust find somewhere more suitable.

I think you're confusing something here - 92dB would be OUTSIDE the car, probably measured near the exhaust?

For a free-flowing exhaust thats still fairly quiet (sometimes inaudible when cruising at 50-60), make sure you get 2 mufflers, no resonators or anything. I've got a 3" oval magnaflow muffler at the rear and another 3" oval muffler in the middle. Being a wagon I need it quiet to reduce drone!

Its definitely quiet enough but not as quiet as stock.

To make it quieter and still get good flow, use twin pipes...although this will cost more.

It seems you either get good power, or a whisper quiet exhaust, but not both. Also I wouldn't bother doing other mods when you have the stock exhaust, except maybe just an SAFC or something - to maybe save a bit on fuel? Other than that, be aware that adding more boost pressure (ie. more psi) will likely just put more stress on your turbo without actually flowing more air through your engine (it could actually flow less!). psi is a measure of pressure, not necessarily airflow. :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
    • Hi.. Just another problem. So maybe you can help. I(my mechanic) done swap from my RB20DE NEO to RB25DET NEO. Everything is OK but we have a boost cut. Coils/Plugs are ok...AFM is ok. ECU is ok. I have Walbro 255 but it "changed" sound few months ago(you can hear it ouside) you did not hear that when it was new(maybe faulty?) Sooo...what now? What can cause this boost cut? It is even when you standing still...
×
×
  • Create New...