Jump to content
SAU Community

Recommended Posts

I have put some 6.5' speakers in my r33's door skins and while i was doing it i noticed that my door leeks through the window..but there is drain holes at the bottom of the door to let the water run out, so im assuming that the doors were designed to hav a bit of leakage..does it matter if my speakers get wet?? Is there a way i can protect the speakers to stop them getting wet??

Link to comment
https://www.sau.com.au/forums/topic/169000-door-speakers-getting-wet/
Share on other sites

Did you retain the factory door pod. I just cut mine to fit the 6.5" speaker. It covers the top of the speaker to prevent water dripping on it. You might be able to make a fibreglass box for them or something in the door. Thats what I am going to look at shortly.

Nah when i bought the car it didnt have any door pods in it because there was no speakers in it at all..i mite just get some sound deadening and use some of that as a 'roof' as mentioned in the thread about how to install door speakers into an r33..because i just mounted mine straight onto the door skins lol and its pretty rugged haha..

Ah ok no probs. Yeah what you are saying might be the go. I will have to check out this sound deadening stuff. I have got my speakers installed in the doors behind the factory door trims so you can't even tell that they are there. Had to bucher the pods slightly to fit the speaker in tho.

Oh will they?? How much space is there between the door frame and where the window comes down?? (So in total how much space do i have to mount the speakers behind the door skin??)

Edited by jUsT-dRiFt-iT

I used the factory pods to make sure that i didnt have this problem with the window. I used some type s alpine splits in the doors and the speaker just fit in ok. The magnet is very big and just squeezed into the pod after hacking this little ridge off on the pods. But I think there is a little bit of room between the speaker and the actual door trim grill etc. The alpines were quite deep but seemed to fit ok. But if you have already hacked a hole in your door trim I would be more inclined to mount them thru the door trim so ya can see them. My aim was to make my audio setup look fairly stock. ie less likely for people to see and want to break in and steal them.

The proper pods shouldn't be too hard to come by.

Good luck

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yea that's a fair assumption. I'm presuming they call them solid lifters as they have no moving parts like hydro lifters. 
    • I believe you're confusing WMI with water injection. Looking at that graph, the 93aki+WMI car is making more power than C16 race gas. Boost juice, which is what I also run, is Snow Performances 50/50 premix. 
    • GCG is a good company, they're a major distributor for Garrett in Japan as well.
    • Nah, OEM washer bottle and brake fluid reservoirs are fine I don't know what it is with the plastic that Mazda used, some plastics, like the washer bottle and brake fluid res are fine, and still look new after 20 years use, where as the coolant expansion tank, and PS reservoir, that I replaced with new OEM items when I first got the car, turned yellow and started getting brittle a few years later If the dirty yellow stained plastics didn't trigger me there wouldn't be an issue, but they did, much like the battery bracket....... Meh As for going back to work full time to support car stuff, nope, why, because I own a Mazda NC MX5, not a Nissan R series Skyline 🤣
    • I've never heard of CJ-motor, so can't advise you on them. I'd just go straight to GCG for a GCG highflow though. Seems no point to use a middleman. I'm somewhat surprised that the price on the CJ site is lower than the GCG retail price. Even though CJ would get a discount of some sort, you would hardly expect them to give up so much margin. Maybe the price is out of date? Having said that "I'd go to GCG"...when I did my highflow, I went to Hypergear. I did this https://hypergearturbos.com/product/rb25dethighflow/#tab-dyno-results with the R34 OP6 450HP profile. With the BB centre (extra $400) and intially with the standard boost actuator, but I eventually got him to send me the high pressure one when I got to the point of being able to actually use it. Ends up costing the same sort of money as the GCG highflow, but this is, of course, the turbo that I KNOW has a shorter length core and so moves the comp cover rearwards. The GCG apparently doesn't do that. My mechanic also swears by the GCG highflow, given that we have another turbo rebuilder who does something essentialy the same as theirs, using Garrett wheels. He says it stands up at really low revs and makes good power. I haven't pushed my HG highflow past ~240-250rwkW yet (should have a little more in it, but unclear how much) and it does have a fairly gentle boost ramp. OK, it's much better now that I have gotten my boost controller tuned up on it.  A lot of my earlier unhappiness was because I couldn't keep the wastegate flap as closed as it needed to be (including some mechanical issues). I'd still prefer it to boost up nearly as quickly as the stocker, and it certainly a bit slower than that. So maybe the GCG one is worth the first look (for you).
×
×
  • Create New...