Jump to content
SAU Community

exhaust & PFC, what should I expect from my GTR?

Simmo
 Share

Recommended Posts

Simmo Collaborator

Simmo

Posted
Posted

If I get a full exhaust (3inch or greater) including turbo dumps, and install power fc, maybe 15 pounds of boost, what kind of performance should i expect? Roughly what HP would i achieve? standard turbos aren't much good for much more boost afaik, is this correct? I have a K&N airbox insert, is this sufficient?

Is there anything else I should be doing? oil air separator maybe?

The car is mostly only driven on the weekends, and will attend the odd track day.

Cheers

Simmo

PranK Grand Master

PranK

Posted
Posted

Simmo, by the end of this week, i will have PFC, 1.1 bar, exhaust (on there atm), cam gears and filters and i have been told to expect 230kw @ all 4... so yeah, in excess of 400HP and mid 12's would be easy to accomplish with that power...

JAGR33 Grand Master

JAGR33

Posted
Posted

What? You snapped a driveshaft??? Geez what were you doin??

I've got full exhaust, filters, adj. cam gears, 13psi (0.85bar??), which produced 215 kws at the rears. With stock clutch I managed a 12.3 @ 107mph (Calder Park), so with Power FC and a bit more boost, 230 kws would be achieved very easily..... and maybe dip into an 11 sec qtr.....

Simmo Collaborator

Simmo

Posted
  • Author
Posted

Thanks guys, Prank your using standard turbos? Have you got your car back yet?

mmmm nengun has pfc's cheap atm, tempting!

Whats the best option, use a avcr or the pfc boost control kit?

thanks guys

Simmo

vspecv Proficient

vspecv

Posted
Posted
Originally posted by Nismodified

the limit of the stock FMIC is about 400hp @engine

which is about the limit of the injectors, clutch and such as well.

expect time to be mid to lower 12's pending on how hard you want to launch

standard cooler is good for over 500hp,im running standard and im over 300kw at the wheels.

vspecv Proficient

vspecv

Posted
Posted
Originally posted by PranK

ethan, Rear wheel kw? or 4 wheel? theres a big difference...  

cam gears will be next.

depends whos dyno u use,ive had my car done where i get all my dynoing done in 2wd and had readings on other dynos in 4wd and basically the same.

i guess the difference is the guy who does mine basically does just gtrs and his dyno reads virtually exactly the same as the the 4wd dynos in melb.

same dyno as ethans was done,his car made 240 rwkw and i reckon would read the same on a 4wd dyno.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 persistent issues. P/steering and lag/misfire

      By GTSBoy · Posted

      Power steering is probably because someone has nuked the HICAS CU and you no longer have the variable power asist doing what it is supposed to. How much boost are you running? You are aware that any more than 10 psi on the stock ECU is just asking for it to go to full R&R (that's Rich & Retard, which is effectively Retarded and Retarded!) which kills all the power. Depending on the exact conditions, it can just be runnign on the fat and stupid end of the maps, then the conditions change, you make a little more boost and the ECU goes into panic.
    • Kapr
      Freddy Plenum vs Genuine options RB25

      By Kapr · Posted

      @BuiltNotBought Just as GTSboy said.   If you want driveabilty and more low down torque..keep the stock runners. They are VERY good from a factory. I have them too on my RB25DET NEO and as a GTSboy i have fmic but with stock piping route(i have Blitz intercooler) Iam making around 320 BHP and the car pulls "hard" from like 2,5k all the way to 7k. I have it dyno tuned to mimic N/A power curve and making little less max torque due to the smallbox tranny. But driveability is very great. I had 350Nm below 3k so car feels very quick.   EDIT:  Not my channel but i saw this and i know that is what i want (and i have exactly this)  
    • MissMintyR33
      R33 persistent issues. P/steering and lag/misfire

      By MissMintyR33 · Posted

      Looking to sort out a couple of issues on my skyline  It recently was rebuilt, however rebuilder long story short did not give two flying effs about the work he did. So moving forward it's running but I have two persistent issues 1) it has a misfire / lag type of issue (was at higher RPMs but I had a dead piggy back ecu removed which improved it) now it's not as bad but still does it at random, I thought it may have been a boost issue I'm running an older turbosmart dual stage controller, turbosmart told me to try running off gate pressure however it still has a lag at random times. It has New MAF, maf plug, coil packs, sparks, CP harness.. injectors tested and cleaned. Factory ECU. 2) Power steering issue. It is tight as anything. Flushed power steering, rebuilt my pump because the bearing was shot. Flushed again still tight (mainly when parking and going slow into my driveway etc)  No kinks in hard lines, replaced the lines I could see had cracks. Still tough to steer.  I was told to shim a coin and place into the solenoid plug? Is there anything else. My steering angle sensor also has a issue. It's a used one I replaced, does it need to be calibrated? I feel like I've tried everything and this car is my voodoo doll.   
    • Dose Pipe Sutututu
      Neil's R33 Gts-t Build

      By Dose Pipe Sutututu · Posted

      Holy shit... wow!!! I totally missed this
    • MBS206
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By MBS206 · Posted

      One main filter. Each tank has a prefilter to keep rocks and small children out, then the big main filter that also does water separation. Clogged the first one so bad it was like a rev limiter at 3200rpm. Literally just like dropping the throttle off and maintaining rpm!
×
×
  • Create New...