Jump to content
SAU Community

Drag results ...

hippy

By hippy,
in South Australia

 Share

Recommended Posts

Freebaggin Proficient

Freebaggin

Posted
Posted

Clint32,

Shit, I saw your reply and thought doh myself, as I forgot about your runs. I assumed the E/Ts were better than mine due to the very quick top end. Get your launch OK and it'll be a 12s job for sure. Chris32 had trouble getting a good start/rpm balance too.

Bugalugs Enthusiast

Bugalugs

Posted
Posted

Thank u Ivan/RPM Performance for a great day.

It was my first time down the 1/4 so it was nice to do it without a big crowd.Part of the reason why i wanted to do this was to backup my dyno results from the dyno day at Tilbrooks and prove that it was no fluke.

My best was [email protected] 60` and as Freebags said i did do a 106.99mph 13.5.

It was good to catch up with you guys again and when i'm settled into my new house i should be able to get out crusin again.

Freebaggin-I'm not sure how long that gasket is going to last being that you are missing 2 studs.You may have to order that T88 earlier than you thought so they can fit and fix all at once to cut cost.

Grepin-I`m still baffled by your low mph.I spose just let WW2 begin and kick F/B`s ass then.

Matt

Chris32 Veteran

Chris32

Posted
Posted

Yep, it was a top day, big thanks to RPM

I had a few good runs, but I really struggled to get it off the line. My best run of the day was 14.03 @ 104.9mph with a 2.5 sec 60ft

Don't reckon the hard track style suspension and cheap Falken's helped much, maybe next time I will get some decent rubber and try and knock 1/2 a second of my 60ft times.

At least after 8 runs nothing broke

Chris

Maxx Veteran

Maxx

Posted
Posted

Thank u Ivan/RPM Performance. Specially borrow me the tyre pressure gauge :rolleyes:

never been to drag race b4, i was VERY excited. have 2 15sec pass with 32 psi tyre ,then i borrow ivan's gauge and release the tyre pressure to 22psi and done a 14.5.

being the slowest skyline (tubro) of the day,[email protected] with a 2.299 60'.With same mod of other member(exhaust, intercooler, boost controler) I found that even i have a OKAY lanuch, my car start get slow down at 2 or 3 gear, (seems the boost pressure can't keep at what i set) i try to adjust from 12psi to 13.5psi and guess what, i did worse time in 13.5 psi - [email protected]

i have order a e-manage from japan this morning after doing some disappoint time. With better tyre, hopefully i can break into 13.5 at the next meeting.

after 9 runs, my heavy duty clutch is not heavy duty anymore :)

Maxx Veteran

Maxx

Posted
Posted
Originally posted by hippy

agree with u skyppy .. i saw alot of ur runs tin .. u also got not so good launches .. that greddy emanage would cost something like 1k?? spend it on ur suspension .. lighten flywheel ... tyres ... its all power and torque ... not that i know anything about drag racing .. :rolleyes:

i already got tein HR suspension on my car

i was quite interest at lighten flywheel, but someone told me they will affect the drive quality. Actually anyone who have it, can u told me what is good or bad after having it? but anyway, it won't be purchase until i blow my clutch

tyre was a definate, they are quite worn, i am still waiting my aftermarket rim arrive from oversea, so tyre will be purchase when the rims land.

from the MPH i run, even i got better tyre, i might be just able to break into 13sec, as my aim is low 13 or even high 12, i need more power(more boost). When i get the e-manage, i can have more power and even running higher boost, i can buy them for around $700, and i already have a e-01 to match, rather than a pfc for doulbe the price, it seems not a bad idea...

Cubes Grand Master

Cubes

Posted
Posted

Lightened flywheel's only really improve your acceleration from lower in the rev range. When at the drags you are always operating at the top end of the rev's i.e 5500-7000rpm so apparently the lightened flywheel is not benificial.

I have a chrome molly lightened flywheel and noticed at the lights it was easier to take off, gears rev match heaps quicker. For the street lightened flywheels are quite good. No loss of drivability or fuel consumption.

Maxx Veteran

Maxx

Posted
Posted

the best things to improve the time instead of spending more on the car, is improving my launching skills and shifting skill.

i think i shift alright... :D

Maybe a bit of weight deduction on my car, but more important, is LOSTING weight myself!! :D

i was 75kg when i come to Aus. 3 years ago, and i am near 100kg now, if i can lost some weight to i used to(75kg), the car is 25kg lighter,plus take the audio (2xkg) and spare tyre (10kg?)out, definatelly can be 1/2 sec faster!!!;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sinn3r
      R34 Skyline climate control unit transistor

      By sinn3r · Posted

      perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • dbm7
      R34 Skyline climate control unit transistor

      By dbm7 · Posted

      Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • 25RBGT
      Got this r31 silhouette flood car to rebuild.

      By 25RBGT · Posted

      First time we have seen lights 
    • Wazmond
      WGNC34 - floor mats

      By Wazmond · Posted

      I think Fitmit had some, have a look on there (theyre Australian as well)
    • soviet_merlin
      Howdy Y'all

      By soviet_merlin · Posted

      Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
×
×
  • Create New...