Jump to content
SAU Community

Wires In Boot (r32 Gtr)

whiteboy01
 Share

Recommended Posts

whiteboy01 Collaborator

whiteboy01

Posted
Posted

Hello guys fellow reader new poster here! I have brought a GTR a few months ago and now i have a major problem. There is 2 lights on the dash which are the 4WD and ABS lights. There is plenty of threads about this problem but as far as i know but they all point to the box in the back (HICAS? or ECU?) with lights but i can't find the lights. Now when looking there i notice that some wires are disconnected and looking quite wierd. If you could point me in the right direction that would be swell!

I have attach pictures of the wires that are of concern!

Cheers again.

post-36471-1181379859_thumb.jpg

post-36471-1181379870_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/172097-wires-in-boot-r32-gtr/
Share on other sites
djr81 Grand Master

djr81

Posted
Posted (edited)
Oks guys a looked at the little box with the life and i get 13 flashes! G-Senor right?

According to the good book error code 13 is a fault in either of the two fore & aft G sensors.

But as has been said you need to check those wires to confirm their function & to determine whether or not they have been mucked around with.

Edited by djr81

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Nice....looking forward to that update
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...