Jump to content
SAU Community

Recommended Posts

ive got a series 2, but i thought it still needed cutting?

what power is the arc 105mm core good up to?

Im pretty sure but not 100% that no cutting is required. my mate was thinking about replacing his front bar with a series 2 bar cos it didnt need cutting. he didnt end up doing it cos of family stuff

Link to comment
https://www.sau.com.au/forums/topic/172288-smic/page/2/#findComment-3174857
Share on other sites

14 will be safe, if your has the supporting mods.

AS for stock turbo untuned, you will get more response and power by running less boost.

Just because you run 14psi doesnt mean your car will going any faster.

Run 0.8 bar max.

That is 10psi.

I can gurantee you the responce will be much better with lower amount of boost.

Once your car is tuned to run a little higher boost then go for it.

Get a 34 side mount, which can handle up to 200-210kw.

ARC are to pricey. 34 cooler will do the job fine.

Why would a car running lower boost be more responsive than a car running higher boost? Do you mean to say a stock turbo with a max 10psi will reach the 10psi faster than a stock turbo running 14 psi would reach 10psi? Or do you mean to say the turbo running 10psi will seem more responsive because it has a lower max boost and therefore reaches it quicker than it would reach 14psi?

Link to comment
https://www.sau.com.au/forums/topic/172288-smic/page/2/#findComment-3175137
Share on other sites

^

For -- (stock ecu, turbo, smic)

1) you car will be running rich firstly.. Every skyline does!! lol

2) You will see more flat spots with higher boost levels..

3) Running high amounts- your plugs may foul up.. So you need to regap the size.. to make up for it..

4) From personal experience and seing it from friends car, when they first started.

5) on a hot day, having that bit extra psi or so wont help you at all.. Car will feel slugish when you really push it, more so with higher boost..

Im just speaking from experience, and i maybe im wrong.. Your car may act differently..

But i found that running that bit less boost, made my car more responsive.. ie i turned it down from 0.8 to .7 bar

FACT: At the drags.. Im like lets run more boost.. at 0.8 i got like 14.5 at best for 3-4 runs.. A guy suggested to me at the drags to turn it down.. so i did one notch.. got a best of 14.0 flat..

BUT who knows, maybe my reaction time was just better...

Maybe others can back me up on this?

either way my car feels better runnin a bit less boost.. that is 0.7-0.75 bar.. I felt no flat spots at track day..

and i still got stock ecu, turbo and smic..

i noticed you posted in that 34 wreck thread from some time ago, the guy was selling his cooler for 80 bucks. did you end up buying?

rang him the night before to confirm meet up.. he goes his dad ran over it?? hmmm

250 does seem pricey.. But they normally start at that price and drop down.. to 150-200

Cost that much because they know its a cheap upgrade for the 33..

on a side note, what is everyone's opinion of china cores?

Very good coolers.. They do the job.. 0-300kw.. has been proven..

Many threads on this topic..

Cores are all the same.. Comes down to which copy has the better pipings..

AS for cutting the bar on the s2, i will confirm with you tonight. My friend does cooler installs.. So i will ask him about the series 2..

Otherwise im sure there are heaps of members on here with s2, with fmic..

Edited by siddr20
Link to comment
https://www.sau.com.au/forums/topic/172288-smic/page/2/#findComment-3182066
Share on other sites

Im pretty sure but not 100% that no cutting is required. my mate was thinking about replacing his front bar with a series 2 bar cos it didnt need cutting. he didnt end up doing it cos of family stuff

i was at Bel Garage one day when they were isntalling a JJR fmic into a R33 s2. they said that if you do it right then you wont need to cut anything away ie fan baldes, front bar..etc..

i have an Apexi front mount with same side return piping which costed an arm and a leg which didnt need hacking either. small core but does the job easily.

Link to comment
https://www.sau.com.au/forums/topic/172288-smic/page/2/#findComment-3182097
Share on other sites

well ive actually helped a mate install a just jap front mount in his series 2 skyline, this was a few years ago and im 100% certain that we had to cut some of the bar ( on the bottom of the hole under the 2 lights in the bar) because the piping was hitting against and we couldnt put the bar back on. not sure if anything else had to be cut.

But wen we finished it looked very neat, and you couldnt tell we cut anything

Link to comment
https://www.sau.com.au/forums/topic/172288-smic/page/2/#findComment-3182138
Share on other sites

to all the people that said they'd double check, any confirmations that its possible to install a fmic with absolutely NO cutting?

SiR RB: Id expect Just Jap, like other generic core/pipings, to need bar modifications but a brand name cooler might not.

Edited by ak_stylez
Link to comment
https://www.sau.com.au/forums/topic/172288-smic/page/2/#findComment-3185207
Share on other sites

I just fitted an R34 intercooler to my series 1 stagea. It cost me $80. Bunged it in on the weekend. There is the obvious difference in size but also if you examine the cooling fins they are perforated on the R34 intercooler meaning greater surface area to volume ratios for heat transfer.

It has all the power headroom I need for a 220awkw-ish turbo upgrade. I am also going to run a set of cams in the motor later on so the average power will be significantly up adding to the potential heat load but, I am completely unconcerned about heat soak and the abillity of the R34 intercooler to do a decent job. A water spray kit gives me everything back I might lose on a sustained flogging and costs bugger all to make.

You can skin a cat lots of ways. The R34 intercooler is a good stepping stone till you make your mind up about the actual power goals and how much money you don't have to spend on other important supporting mods.

Edited by rev210
Link to comment
https://www.sau.com.au/forums/topic/172288-smic/page/2/#findComment-3186361
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...