Jump to content
SAU Community

Recommended Posts

I lost my FAST install in a PC rebuild accident... :)

Can someone tell me if an S13 with a CA18DET(89) and a SR20DET(92) have the same clutch master cylinder?

i would so no, none of the numbers line up

Would you know the part numbers for the door window seals that are connected to the interior door cards on a R32 four door by any chance? mine are more wrinkled than my gran!

RHF 80834-01U00

LHF 80835-01U00

RHR 82834-01U00

LHR 82835-01U00

  • 2 weeks later...
  • 2 weeks later...
Hi Neil , is there a part number for the original R34 GTR MFD the whole unit including the housing, thanks

cheers,

David.

sorry bout late reply. There are 4 different part numbers for the MFD less the housing 2 for pre 08/00, and 2 for post 08/00

Pre 24845 AA414

Pre 24845 AA415

Post 24845 AA416

Post 24845 AA417

the housing is seperate Part No. 68411 AA400. hope it all help

sorry bout late reply. There are 4 different part numbers for the MFD less the housing 2 for pre 08/00, and 2 for post 08/00

Pre 24845 AA414

Pre 24845 AA415

Post 24845 AA416

Post 24845 AA417

the housing is seperate Part No. 68411 AA400. hope it all help

Thanks Neil , awsome help, most appreciated.

cheers,

David

  • 2 weeks later...

Hi,

Im hoping that you can help me find the part number for my brake master cylinder. The details are below:

CAR: 1993 R32 gts-t M-Spec with ABS

CHASSIS #: HCR32-292253

MODEL #: KRCR32RGFS3 FA

It appears to be different from most other R32's because apparently mine is a very late model R32 and it recieved a brake upgrade. I think the master cylinder has a 1 inch bore rather than a 15/16 inch bore like most of the others. The master cylinder has BM-50 on the side of it if that helps.

Thanks for any help,

Shaun.

can i please have part number for r33 gtst 1996

turbo studs (that bolt dump pipe on)

manifold to turbo gasket

thanks in advance

Are u sure they are studs my listing has them as bolts in any case Part No. 14434-V0301

and gasket No. is 14415-4P200

gah i dont have FAST installed on this puter, can someone please confirm which part this is.. is it the door trims that sit between the top of the door and the glass??

R32 Skyline

8083404U00

That number is a good number depending on a few other things with your care

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...