Jump to content
SAU Community

Recommended Posts

When my clutch is out somethging is making a whining noise, but when clutch is in I think the whining noise goes away.

But when I put the clutch in when in neutral I get a rolling, tapping noise. I only ever get this noise in neutral

Anyone got any ideas, the whining noise is starting to shit me.

Link to comment
https://www.sau.com.au/forums/topic/173122-whining-noise-when-clutch-out/
Share on other sites

I think that the sound that you are hearing is from the clutch bearing. When you have the clutch in neutral the fingers of the clutch might be just scraping on the bearing. And when u push the clutch in, it (bearing) engages with the fingers n stops slipping on them.

I have a similar problem in my subaru. I put a new clutch in but i think i stuffed up by not putting enough grease on things. The clutch bearing seems to be still touching the fingers of the clutch when i have the car in neutral. I can;t seem to change it cos if i losen off the clutch cable i can't get enough throw to disengage it.

Don't take this as gospel. It is just my ideas.

Yep sounds like gearbox input shaft bearing, Unfortunately its a common problem in the skyline boxes.

Best way to diagnose is park car in shed/ garage, start car, gearbox in neautral and listen for

Grumbling bearing noise (sometimes whirring) Then press the clutch pedal in. If noise goes away it indicates the Input shaft bearing in the gearbox, if Noise still there its the throw-out bearing of the clutch. Hope this helps, Have found redline Shockproof oil works wonders in these boxes to. Should change gearbox oil at least every 40 000km.

Yep sounds like gearbox input shaft bearing, Unfortunately its a common problem in the skyline boxes.

Best way to diagnose is park car in shed/ garage, start car, gearbox in neautral and listen for

Grumbling bearing noise (sometimes whirring) Then press the clutch pedal in. If noise goes away it indicates the Input shaft bearing in the gearbox, if Noise still there its the throw-out bearing of the clutch. Hope this helps, Have found redline Shockproof oil works wonders in these boxes to. Should change gearbox oil at least every 40 000km.

I definetly got the whirring noise in neutral, is it real bad, get it fixed straight away?

I definetly got the whirring noise in neutral, is it real bad, get it fixed straight away?

It happen to mine about 10 months ago. A throw out bearing. The gearbox guy said it does no harm you just have to put up with the noise, to fix it is a major rebuild. He put some redline oil in it and told me to come back when the box shits itself from somthing else, away i went. And yeah the redline oil does not stop the noise, just better gear changes. :D

  • 1 year later...

Hey I just started to have this happen to me, can anyone confirm this needs a major gearbox rebuild? How much damage is it doing? (Getting kind of paranoid cause of the GOR cruise in 2 freaking days)

I'm sure mine is the input shaft bearing too. Started making noise after a spirited drive, hilly stuff.

It only got rebuilt last year with new stuff, but it is take 2x stock HP.

Still annoying that it happened. Hasn't seemed to get worse though and doesn't make noise when coasting along or deccelerating, or when pushing in clutch sitting still.

in my experience its gonna be different for every gearbox i pulled mine apart recently and the counter shaft bearing in the carrier plate was farked but input shaft bearing was ok.

i had the same problems as everyone else though, mine just got really really loud so i swapped it

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I have done a lot of research before posting here and on gtruk forum. couldn't find anything. I have my gauges all part except the needle itself. the needle has a extremely small hole in the center, but the shaft going to the needle is extremely small and appears to have nothing to index it either. doesn't seem strong enough to simple pry or pull without damaging something. Already tried the old spoon trick on a extra triple meter I have from a gtt, but no luck. the center cap comes off easily but the hole in the meter face plate aren't big enough to get over the needle itself. figured this would be my best place to find someone who might have actually removed theirs. wonder if there is some type of small pin press tool to push the pin in while pulling the needle base off.
    • Ok...its taking me long enough to finally do this.  Feck financial security...heart disease will get me soon enough anyway So welcome to the garage..."Clem" Belsil80 has been running a 370Z in Super TT series. So after entering with him in last years Winton 300 i figured I  need my own car. Seems SAU Vic race cars need to be yellow....{tick} Reckon with enough motor i will be able to make up for the lack of talent and stay ahead of the 370Z... but the LS powered S13 and E36s are a ways up the road Aim is to have a car that doesnt stop or turn but has a bit of shed built motor with jam...maybe some cream  First step is getting this ex drift car log booked I am keeping faithful silver car. As the road-club car gets upgrades the race car wil get the sloppy seconds
    • Assuming that they will come off without damage at all.... i would have thought just pull straight up off the spindle with a something or other than can reach underneath. Have you searched for youtube vids of people doing similar on R34s or any other Nissan from the same vintage? They should be the same technique, in all likelihhood.
    • Keeping in mind that sandblasting is really aggressive on softer metals like cast alloy, and you can do damage that you might regret. For trash wheels, not a problem. For wheels with value/scarcity issues, etc.... perhaps a less aggressive media is a better choice?
    • Don't get all high and mighty. Experienced spanner wielders know exactly what effort is required to release an Oof.
×
×
  • Create New...