Jump to content
SAU Community

Recommended Posts

hey all jus came back from his sellers place in inner west (close to bankstown) and the parts available are genuinely there. great guy with good attitude... and i hope seller doesnt mind that i post his contact number up so everyone can stop making posts about it.

contact number: 0416 554 283

looks like alot of trim parts are gone, driver's seat is gone, no floor matts, no rear seat, side mirrors are there, rear lights are there, anything front right of car is pretty much gone, radiator gone, motor is good, doors there, windows there...err..dash is there.....it is a WHITE coupe, NON TURBO.

hope that has saved alot of unnecessary questioning and just call him if you need anything, he wont bark.

great seller! :yes:

Dom

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

hey where in sydney you located? i need a bootlid key hole nissan thingo (blew mine out with the sub :rant: ) probs need front rotors as well (well need the drivers side one more...

rofl! aheahea is that even possible?

ur sub must be powerful!

lol

Updated price list.

Rims with 80% tread on all four - $600 Price drop $500ono

Bootlid - $100

Spoiler - $80

Rear bar - $150

Tail lights - $70 each

Window regulator - $80 each

Steering wheel no airbag type - $80

Dash cluster 128kms - $80

RB25det Airbox SOLD

Passenger side gaurd SOLD

Interior - $200 complete will seperate parts

Passenger pwr window switch - $50

Driver side pwr switch - $60

Rb25de - $500ono

Dash cluster surround - $50

Parcel tray - $50

Passenger side door - $100 without reg or door trim

Ignition barrel, key and matching door locks - $100

Climate control unit - $40

Floor carpet - $50

Middle console - $30

Rear window - $80

All prices are negiotiable.

PM for any other parts as car is complete.

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
    • Shimmed or shimless, still solid, no hydraulic pump up stuff.
    • They have said food will be limited. Mainly meat pies and sausage rolls from memory. But they have a coffee van!
×
×
  • Create New...