Jump to content
SAU Community

Recommended Posts

  • Replies 190
  • Created
  • Last Reply

Top Posters In This Topic

will hopefully be sorting mine out by the weekend too ;)

btw is doesnt get rid of the 180 cut still need a SCD or PFC or similar

mines doesnt have the speed limiter on mine i dont knoe when it kicks in but at malla i got past 180 and it didnt kick in so who knoes??

no problemo...enjoy!

Hey Jeffworld, tried to reply to your PM but your inbox is full, let me know when there's space and I'll re send the PM.

alternatively, PM Justin911 as he'll be able to answer your question :)

installed this today, everything seemed fine, until i started the car and the needle jumped up to 33km/h at stand still.. not sure what the problem might be? any help?

should i take it apart again and re-adjust the needle?

or could it be my soldiering of the points at the back?

Cheers.

Edited by EVL-R33

Installed mine today - Looks sweet

Thanks guys for organising this buy - very happy

(I found that it was easier to install the cluster into the car without the clear cover and install the needles whilst the ignition was on to get the correct placement - another hint, make sure you know how much fuel is in the car before you change them over, so you know where your needle is supposed to be pointing)

Now I just need LED's :laughing-smiley-014:

post-37249-1189754581_thumb.jpg

post-37249-1189754769_thumb.jpg

Edited by Jaron

on 2nd though went for drive today i may be lucky and fuel is ok but as i have to redo my speed will be taking dash apart again and going to a dyno to set it up

i modified my tacho gauge so i can see my Slip light and 4WD fault light

Before original Tacho

p1000653sx9.th.jpg

After installing the Tacho and Dummy Boost gauge :laugh:

p1000669qs5.th.jpg

you can now see my slip light and 4wd warning light

i drilled the my orriginal guage and used that as a template to drill through my new face :)

na no boost gauge cause is factory NA and still doesn't work because no mechanism there but looks the part I've got a after market boost gauge

i actually bought the car turbo and suspect the people who did the job used an engine out of a stagea due to mine being GTS4

if anyone has #6 soldered (mine did for some reason) you need to desolder her

um i would think not the instructions were pretty clear and even showed #6 bridged

in my opinion as per Amec's instructions is how the job should be done

BTW i had mine on the Dyno on Friday the recalibration is spot on so if #6 did need to be de-soldered then my speedo would of been way out

hehe i had issuing installing mine and i pm'd amec and he said to try de-soldering #6. Also dezz doesnt have #6 on his soldered to start off with. His a 98 model. mines a 96

i tested mine with my pfc speedo and a gps :laugh:

Its wierd cause it seems to work with a few diff combinations... long as its working for everyone though :)

It wouldnt be way out btw, only out by like 5-10km below 100km if it was wrong.

um i would think not the instructions were pretty clear and even showed #6 bridged

in my opinion as per Amec's instructions is how the job should be done

BTW i had mine on the Dyno on Friday the recalibration is spot on so if #6 did need to be de-soldered then my speedo would of been way out

Everyone should have received their kits by now, as I think the last kit was received today ;)

Anyone that hasn't left feedback as yet, it'd be appreciated if you could do so, and I'll return the favor

As far as trader rating feedback goes, it'd be awesome if everyone who participated could do the following

leave feedback for me here : http://www.skylinesaustralia.com/forums/in...r&mid=14874

leave feedback for dez (keeping in mind he is responsible for the majority of the work involved with this group buy) here: http://www.skylinesaustralia.com/forums/in...=22515&la=0

and also for Amec (feedback on the product itself) here : http://www.skylinesaustralia.com/forums/in...r&mid=27224

If everyone could do that it would be good that the people involved were recognised for their efforts in the GB

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
    • Shock tower brace is in +5Kw....LOL  
×
×
  • Create New...