Jump to content
SAU Community

Recommended Posts

i have a 1998 semiauto r34 gtt. with intercooler, airfilter, BOV .and i drive it normally.but it just can keep going for about 280 km with a full tank.

i use #98 petrol, and fill in about 48 liters to make it full when the indicator tells me there was few petrol. is the fuel tank of gtt 50L ? i just want know a normal situation of the gtt's fuel consumption thanks a lot.

i have a 1998 semiauto r34 gtt. with intercooler, airfilter, BOV .and i drive it normally.but it just can keep going for about 280 km with a full tank.

i use #98 petrol, and fill in about 48 liters to make it full when the indicator tells me there was few petrol. is the fuel tank of gtt 50L ? i just want know a normal situation of the gtt's fuel consumption thanks a lot.

Hey Dude I have a R34 GTT tiptronic auto Hybrid fmic, full exhaust from turb back,Greedy ebc, Safc2,BOV, POD, and my car gets 300 km to a full 50 lt tank it sucks what is wrong ????????????????? :thumbsup:

Edited by YPLAY4
i have a 1998 semiauto r34 gtt. with intercooler, airfilter, BOV .and i drive it normally.but it just can keep going for about 280 km with a full tank.

i use #98 petrol, and fill in about 48 liters to make it full when the indicator tells me there was few petrol. is the fuel tank of gtt 50L ? i just want know a normal situation of the gtt's fuel consumption thanks a lot.

its all in how u drive the car keep it off boost and u will do fine. i have a r32 gtst with fmic dump pipie full exhaust stock cat uped boost pod filter. and i get 450 to 500 normaly but when i give it some i get bout 300 to 350 and thats not even on empty.

GTT tank is 65L. If you used 48L to top up then you have approximately another 17L left. 280kms to 48L is still pretty rich. I just filled up my tank today with 47L after having done 360kms.

The usual culprits are O2 sensor, spark plugs, AFM...perhaps take it for a tune and service.

NISMO is right, the tank is about 65L. I'll normally get about 400kms region to a full tank. I don't run it till the lights come out though. Got a 3" turbo back, fmic, pod, ssqv, boost at 12psi, foot is a little heavy at times :nyaanyaa:. Really depends on how you drive.

changing the o2 sensor will help, changed mine and i went from 300km a tank to about 430km tank.

This sounds more like it. I have a s2 stagea (r34 engine, gearbox), which is quite a bit heavier than a skyine and on 48L my car will get over 400km around town. Its got 160awkw too so its not stock either.

My guess is that you should at least be getting more than 350km on this amount of fuel, modified or not. If its doing less than that, you need to either adjust your driving style or look for whats causing the problem - eg. check your O2 sensor. :D

A good free-flowing exhaust, SAFC or similar, and improved ignition timing will help your fuel economy as well, not to mention a bigger turbo (off boost while cruising). :D

As others have previously mentioned, the fuel capacity is 65L so try pumping it as much as possible. Reducing the use of boost should help acheive more k's. If not u better get it checked out.

my 2c worth

the following could be causing it too

Dirty air filter - causing the motor to work harder than it needs to , cause its not getting the airflow it needs

Slightly too thick oil - are you using the correct grade of oil in it ? I mistakingly used some stuff that was too thick in another car I had - and I did notice a drop in economy

change the o2 sensor as previously advised

have you ever had the car on a dyno? the dyno readout of AFR can definately tell you a LOT about what your motor is doing. I think if you were chasing the most kays per tank .. an after market ecu or a few add in mods like a SAFC and a SITC ( I think thats the one that controls engine timing )

if you got the above fitted . and spent some time and money on a dyno tune.. you would probably get more power and use less fuel. dont forget if a motor is running really really rich .. then its safe.. but .. its just pissing fuel out the tail pipe , leaning the mix to a leaner (yet still safe ) will yeild more power and less fuel consumption - but dont fall into the trap though of getting a bit more power and driving like a maniac - cause of course your goign to use more fuel

good luck matey!

if you can afford it run with a good fuel like BP ultimate 98 - just less chance of it pinging/detonating if you push it hard.

Oh and .. have a look around .. because you can find " equivalent " o2 sensors that are usually less expensive. To be honest I am not 100% certain if the equivalent o2 sensor will be " just as good" as a geniune one. But its worth a go.

Make sure you get some good crimp connectors to join it up , as my previous experience with this proved that the wires they use on o2 sensors are impossible to solder ( I think they are stainless? )

thanks everyone .now i think i catch the key point.

another question : which grade of petrol should the gtt fill? #98?

thanks everyone .now i think i catch the key point.

another question : which grade of petrol should the gtt fill? #98?

As this had been covered many many times, anything just 98 Octane will be just fine. Be it BP Ultimate, Caltex Vortex 98, Shell V-Power, V-power Racing, Mobil Synergy, they are all fine. Just a personal preference on which 'BRAND' one prefer.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...