Jump to content
SAU Community

SAU Caps & Beanies... just made a deal, any1 want one?


Recommended Posts

  • Replies 246
  • Created
  • Last Reply

Top Posters In This Topic

ok, i upgraded finally to poser 5, and to my surprise there's a new updated cap model in it!!! :)

that means good quality cap renders... here are a couple I did from some of the logo designs I made. Now I can make your design instructions into pictures, so fire away guys. I'll need good desciptions... which logo, where, what orientation, what angle etc etc.

here's one design to get yas started:

cap1.jpg

cap2.jpg

Hey i think that that last design is choice, What design is it going to be for the beanie, any desisions?? not that it matters really though. Could you have it ready for this weekend though as am heading down to the snow. hehehe

Put SAU in white in the middle with the after burner tail lights on either side, on an all black cap. on the back (and I know everyone will say I'm a nerd) the url

Beanie just have the sam SAU logo as the cap.

my 2c

Cheers.

Guest DIESEL

Dude the design is sick! The monogram block with tail lights looks good. ASnd with the skylines.com wrap around the base or rear would compliment well. Put me down for 1x white cap, 1x black beanie, cheers. Top work on the organising Funky.

the peak will be the same colour, I just couldn't get a render with the same colour that looked clear, it jus looked like a massive black blob

i'll take a white one, red one and black one of the bottom one but put the URL on the side or back of it.

Put me down for a white skully too...

altho if u could make the midlle ones logo bigger so it goes over more of the heat it would look even better.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thank you, 100% the intent. New coils were due and the 17" sixers look/feel loads better than the stock wheels. The aero options are so spot on.   Thanks for the warm welcome, all!
    • 98 r34 gtt Been rocking my latest setup and car running like never before. Have put a good 200 miles on it since all the latest changes and additions. everything is dialed in and have been driving it a bunch.   However, all a sudden last weekend as soon as I pushed throttle passed 4k and the engine stumbles, (slow or fast acceleration) hesitates and doesn’t go above 4100 or so, like a misfire. Everything else seems fine. I had a “good” set of coil packs that I removed from car when I first got it when I changed them over to new coils. I swapped out current ones for those, but no change. I also changed the plugs, no change. Seems to rev over 4 when out of gear with no load just fine no “misfire”, but as soon as its in gear with a load of any kind, it “misfires” as soon as rpm drop back below 4 k it runs perfectly, smooth, starts, restarts and drives fine as long as I keep it below 4 k while in gear. All readings look fine, no CEL   Any idea as to what could all a sudden cause an issue when pushing rpms passed 4 k?
    • When you say your cams are 272/262 is that 272in and 262ex?
    • We're arguing semantics. I am saying 45 accel and a 55 deccel ramp are "2 ways". Even a 45 degree ramp and an 89 degree ramp is "2 ways", because it is literally... two ways. The cusco 55/30 ramp is a 2 way. It's two ways. I get it though - in normal nomenclature a "2 way" would be 45/45 or 55/55 or 60/60 i.e the same locking in both directions. And something like 45/65 would be considered "1.5 way". I would then say if we're getting into the nitty gritty then every locking diff is a "2 way" diff and we should not speak in 1.5, or 2 ways but ramp angles instead. Which ofc if one of those ramp angles is 90deg, that side is not doing any locking. :p So Nismo don't obviously sell 3 things. The fact of the matter that they only sell two items really goes to show that there's a 2 way and a "1,5 way" which is really a 1 way. I believe the actual lockup for the 'adjustability' of the GT pro is really just setting preload for when the ramps actually start locking up. It's not changing how much 'wayness' there is. It is (somehow) horribly explained. People just buy whatever diff and go "locks up good bruh" and that's what ends up on socials forever.  
×
×
  • Create New...