Jump to content
SAU Community

About To Do Timing Belt For First Time :s

cosworth1971

By cosworth1971,
in General Maintenance

 Share

Recommended Posts

cosworth1971 Community Regular

cosworth1971

Posted
Posted

Never done it before on a skyline96 gtst

but is the hardest bit the pulley or something else?

just worried the cams may move when i take the belt off( so do i need to hold them in place?)

due to spring preasure?

ive also been quoted under 50$ for a water pump from auto pro but thought water pumps were dear for my car?

axe s Experienced

axe s

Posted
Posted
Never done it before on a skyline96 gtst

but is the hardest bit the pulley or something else?

just worried the cams may move when i take the belt off( so do i need to hold them in place?)

due to spring preasure?

ive also been quoted under 50$ for a water pump from auto pro but thought water pumps were dear for my car?

i'd be double checking part numbers... that doesn't sound right, mine cost $130 from tweakit (probably not the cheapest but can't be that far off) get a manual if it's ur first time (can buy a CD version on ebay for like $15)

But u just have turn your crank to no.1 TDC then your cams should line up with your 0 degree mark there is one on each cam and i think one on the crank (can't remember)

cosworth1971 Community Regular

cosworth1971

Posted
  • Author
Posted
i'd be double checking part numbers... that doesn't sound right, mine cost $130 from tweakit (probably not the cheapest but can't be that far off) get a manual if it's ur first time (can buy a CD version on ebay for like $15)

But u just have turn your crank to no.1 TDC then your cams should line up with your 0 degree mark there is one on each cam and i think one on the crank (can't remember)

I got the manaul for free ,that guy who sells them is a scam! i know he got his at the same place :) it on the web for free

colgf Enthusiast

colgf

Posted
Posted

There is an excellent thread on the STAGEA forum. Covers all the steps to change the timing belt on a RB26 motor , Yes , the crank pulley nut is the hardest thing to undo , its done up to 650ft/lb torque , you may need to make up a pulley lock tool to hold the pulley still while you crack the nut.

cosworth1971 Community Regular

cosworth1971

Posted
  • Author
Posted
There is an excellent thread on the STAGEA forum. Covers all the steps to change the timing belt on a RB26 motor , Yes , the crank pulley nut is the hardest thing to undo , its done up to 650ft/lb torque , you may need to make up a pulley lock tool to hold the pulley still while you crack the nut.

650ft torque do you need a 10 ft extension bar for that or does metal atoms seperate at that force?

are you serious? no torque wrenches will be able to do it up again? i was thinking is it ment to be 165ft pounds?

axe s Experienced

axe s

Posted
Posted
650ft torque do you need a 10 ft extension bar for that or does metal atoms seperate at that force?

are you serious? no torque wrenches will be able to do it up again? i was thinking is it ment to be 165ft pounds?

i don't know what it actually is, but i can tell you it is far,King tight... took me a while to get mine off...

make sure u lock ur flywheel before attempting to undo it..

axe s Experienced

axe s

Posted
Posted
isn't it hard to actuall 'pull' the harmonic balancer off as well? ie need a proper puller?

yeh, only costs $20 from supercheap can get cheaper but they didn't have small enough bolts to fit factory Harmonic balancer...

Duncan Grand Master

Duncan

Posted
Posted

water pumps from an rb30 are dirt cheap - be careful they have less blades that a standard one so they pump less water - the rb30 ones are kind of half way between standard and the n1 water pumps.

I thought the balancer bolt was only 450lb/ft but yes still bloody tight :).

Make sure if you buy bolts for the balancer puller that you get high tensile, at least 8.8 and preferably 12. If the bolts snap you are in a world of trouble getting the balancer off.

crofte Collaborator

crofte

Posted
Posted

Make sure you replace tention spring correctly behind pully as it is ecentric. spring must clip in behind dowel to give correct tention on belt. Get onto VACC for instruction manual for rb25det it will help you a great deal. :)

FOG35 Collaborator

FOG35

Posted
Posted
yeh, only costs $20 from supercheap can get cheaper but they didn't have small enough bolts to fit factory Harmonic balancer...

You actually dont need to buy the bolts because the bolts that hold the cam cover on are the correct size. I did this in mine a few months ago however was a rb20 but i would assume the rb25 would be the same.

And I paid $70 for my water pump from repco.

  • 2 weeks later...
VSPEC-33 Community Regular

VSPEC-33

Posted
Posted
water pumps from an rb30 are dirt cheap - be careful they have less blades that a standard one so they pump less water - the rb30 ones are kind of half way between standard and the n1 water pumps.

I thought the balancer bolt was only 450lb/ft but yes still bloody tight :pirate:.

Make sure if you buy bolts for the balancer puller that you get high tensile, at least 8.8 and preferably 12. If the bolts snap you are in a world of trouble getting the balancer off.

Just buy a new crank bolt from Nissan, the one for my car was only about 10 bucks and you know its going to hold up.

Damn the old bolt was a bitch to get off. 1 metre breaker bar: no good, crank over engine with extention bar under chassis rail: no use. In the end had to use a trucksize rattle gun, which meant radiator and condensor out just to fit the gun down there!

And i went a genuine Holden VL waterpump because it has the no. of blades between std and N1, the car has never overheated. It has a Nissan part number anyway, most likely the same as an R31 RB30E, works perfectly and alot cheaper.

foznice Veteran

foznice

Posted
Posted

I reccomend taking the radiator out. Makes removing the harmonic balancer alot easier and it will probably save your knuckles from a good skinning.

You can line up a torsion bar so that it's up against one of the rad supports or the ground even, and use the starter motor when cracking the big mofo bolt for the harmonic balancer... some people don't like to do that though..

As someone said, just line of TDC 1, and everything should be fine. Just check the markings about 50 trillion times before you put it all back together.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Nismo GT Pro LSD configurations

      By GTSBoy · Posted

      Well, the trouble with that ^^ is: The configuration shown is absolutely a 1-way, not a 1.5-way. There is no way that a 1.5-way can be said to offer LSD action only on acceleration. If Nismo cannot get that right, then it is impossible to believe their documentation. That ^ is not a 1.5 way setup. That is a 1-way.   And so now I have allowed all doubts to flourish and have gone back to look at the MotoIQ video. I originally made the mistake of believing him when he said "this is a 1.5-way" at the ~6:10 mark. Because what he did was take the gear assembly out of the 2-way opening and just rotate it one place to the left to drop it into the 1-way opening. When he dropped it in there, the cam was "backwards" compared to the correct orientation shown in all other photos of that config. The flat shold have been facing the 1° ramp side of the opening, not the 55° ramp side. And I thought, "gee that's cute", but I was concerned at the time, when he put the other ring back on, that the gap between the rings looked like it was wider then in the 2-way config. And then I said a lot of things in my long post on Tuesday that could only make sense if the guy from MotoIQ was correct about what he'd done. BUT... I have now done my homework. I grabbed a frame of the video with the 2-way config, and then grabbed another with the "1.5-way" config, snipped out the cam and opening of that frame and just pasted it direct on top of the 2-way config. I scaled it so that the triangular opening was almost exactly the same height in both. AND.... the gap between the plates is wider with the cam installed in the triangualr opening backwards. That is.... it cannot go together that way. There would be massive force on the plates all the time, if you could even reassemble it.  So, My statement on the matter? The Nismo diff is actually only a 2-way and 1-way. There is no 1.5-way option in it, regardless of what they say. Here's a photo of a real 1.5-way ramp opening from Cusco (along with the 1 way option). And the full set of 1 through 2 way options from their racing diff, which is not same-same as what we'd typically be using, but...the cams work the same. A little blurry, but it comes from this Cusco doc, which is quite helpful. AND.... Cusco do in fact do what I suggested would be sensible, which is to have rings that do 1 and 1.5, and 1.5 and 2. Separately.  
    • PranK
      Hello sau 👋

      By PranK · Posted

      Welcome Adam. Car looks great!
    • Kinkstaah
      Nismo GT Pro LSD configurations

      By Kinkstaah · Posted

      "With a 1.5-WAY, the LSD is effective only during acceleration."
    • TurboTapin
      Nismo GT Pro LSD configurations

      By TurboTapin · Posted

      Well it wasn't as easy as I thought.... and it also wasn't in my original manual which I did end up finding. They discuss the process in the Nismo catalogue though and it requires slight machining. Page 145.  NISMO PARTS CATALOGUE 2020
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      I'm an idiot, my intercooler is rated for 1000hp. I had clicked on the wrong product. Knowing the delta P would be nice, but I'm doubtful I'll do it. Now as for an EMAP, that would be great and I'll get around to it eventually but from my findings in my last post, I'm considering a turbo swap now. 
×
×
  • Create New...