Jump to content
SAU Community

Recommended Posts

  • Replies 433
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Mark,

I was after:

K500 pads front and rear for a R33 gts-t

delivered to Brisbane.

;)

$150 delivered mate.

PM me if you want to order, so I can give you payment details.

Cheers

mate u should b keeping those clips and plates on, otherwise ur brake pistons will b pushing straight onto the pads i rekon and probs crack em.

Sure is mate, until the 15 of May

Sweet, I'll take package 1 please :down:

Package 1:

1 x Full set of ADR approved braided hoses

1 x K750 Front Pads

1 x K750 Rear Pads

$395 Delivered !

hey mate wats the price for k500 front and rear for an r33 gtst deliverd to perth

also is it possible to get them b4 the end of the group buy???

hey mate wats the price for k500 front and rear for an r33 gtst deliverd to perth

also is it possible to get them b4 the end of the group buy???

Price for K500's F&R delivered is $150.

As soon as your payment clears, your pads will be shipped as BW have sold more than 10 sets of pads/hoses already this month.

sorry mark can u just confirm that u know my order is for

k500 brake pads front and rear for an r33 gtst series 2

u just sent me a pm saying it was for the braided lines

just dont want it to get mixed up

cheers mate

Nick

sorry mark can u just confirm that u know my order is for

k500 brake pads front and rear for an r33 gtst series 2

u just sent me a pm saying it was for the braided lines

just dont want it to get mixed up

cheers mate

Nick

Sorry about that Nick.

I've changed your order.

Cheers

PM sent Mark. Keen on legal braided lines for 180sx with R33 series 2 brake upgrade (If that helps in choosing the appropriate lines/ends/ measurements etc.)

Does anyone know how these pads compare to Lucas TRW's?

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I'm actually not sure - I think it was "Stealth Performance" (It really is near impossible to find a FEMALE 1/8BSPT to 1/8NPT male at ALL) but having the thing leveraged on a 90 degree angle on a small aluminium fitting is not too smart. Also in not too smart, I've drilled out the center of the broken fitting so there's maybe 0.00001mm of thread to bite into, so yeah. I may have to get it drilled/tapped/plugged entirely. Given I could conceivably tap a thread/adapter/pressure line in any point in the oil system I suppose it's feasible to run a line to the Nissan Sensor to keep the dash working. Do these exist in AN fittings and the like? Like an AN fitting that has a NPT (or other?) thread as well for putting a sensor in?
    • I would agree.  There will be an amount of boost you could run safely with an otherwise factory system, but it would be low enough to not be worth the cost.  And if you are reliving your 20s, you know a 'little bit' was never enough. Personally, if I didn't want to spend the money, then stick with NA bolt-ons, and maybe a tune.
    • Fuark, at least the motor survived. What brand was the fitting that snapped?
    • Wrong question. There's no point in spending the rather large sum of cash and effort to add turbo, without taking it to the "sensible" limit of the motor itself. If you have to upgrade injectors, etc, then so be it. That is a tiny fraction of what it will cost you to turbo it.
    • Measure voltage at the starter solenoid terminal when the key is at start and it has clicked. If it is really low, then the suspicion falls on the ignition switch (contacts or wiring thereof) as causing a voltage drop instead of sending enough volts to throw the solenoid all the way to engage the starter itself. If it is a decent voltage, then the suspicion is on the solenoid. Might have s horted coil, or might hva dirty contacts. Rip the starter off, dismantle, clean up contacts and inspect winding. It might not be possible to see if there is a short in the winding though. I have a spare starter here that I could measure the resistance of the coil, as a guide to about what it should be, if you need a comparison. <parts hoarder>No you cannot have it.</parts hoarder>
×
×
  • Create New...