Jump to content
SAU Community

Recommended Posts

Has anyone seen a factory Cruise Control on 350GT? Are there any aftermarket options?

Some US delivered G35 Coupes come with cruise control buttons mounted on the steering wheel. Since the throttle is already controlled by the ECU there shouldn't be any need for additional hardware. If the cruise control program is in all ECUs all we need is control buttons.

The control buttons G35 are simply connected to ECU pin 99 via resistors. Has anyone tried this?

Tom

Link to comment
https://www.sau.com.au/forums/topic/178000-cruise-control-350gt/
Share on other sites

yeah i had a look into it actually and even enquired about getting the buttons sent over from the USA but i am waiting to hear back from a few people

the electric throttle helps

i don't think it was offered on ANY 350GT's in japan

the G35's seemed to get a few options that we didn't. eg the auto-dimming reversing mirror with homelink that just arrived at my place today from the USA :)

We have the radar guided cruise system on our 300GT, the front grill has a little dark square in the middle of it, where the Nissan badge sits. Controls distance and also applies the brakes as well, on V35 I have seen this on here in Perth.

Pics on the below link, Post number 8

http://www.skylinesaustralia.com/forums/in...howtopic=149639

Mike

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The roof is wrapped
    • This is how I last did this when I had a master cylinder fail and introduce air. Bleed before first stage, go oh shit through first stage, bleed at end of first stage, go oh shit through second stage, bleed at end of second stage, go oh shit through third stage, bleed at end of third stage, go oh shit through fourth stage, bleed at lunch, go oh shit through fifth stage, bleed at end of fifth stage, go oh shit through sixth stage....you get the idea. It did come good in the end. My Topdon scan tool can bleed the HY51 and V37, but it doesn't have a consult connector and I don't have an R34 to check that on. I think finding a tool in an Australian workshop other than Nissan that can bleed an R34 will be like rocking horse poo. No way will a generic ODB tool do it.
    • Hmm. Perhaps not the same engineers. The OE Nissan engineers did not forsee a future with spacers pushing the tie rod force application further away from the steering arm and creating that torque. The failures are happening since the advent of those things, and some 30 years after they designed the uprights. So latent casting deficiencies, 30+ yrs of wear and tear, + unexpected usage could quite easily = unforeseen failure. Meanwhile, the engineers who are designing the billet CNC or fabricated uprights are also designing, for the same parts makers, the correction tie rod ends. And they are designing and building these with motorsport (or, at the very least, the meth addled antics of drifters) in mind. So I would hope (in fact, I would expect) that their design work included the offset of that steering force. Doesn't mean that it is not totally valid to ask the question of them, before committing $$.
    • The downside of this is when you try to track the car, as soon as you hit ABS you get introduced to a unbled system. I want to avoid this. I do not want to bleed/flush/jack up the car twice just to bleed the f**kin car.
    • But again, the engineers said your cast aluminium would be fine based on the load that would be stretching that section. Same load stretching the bolts in a flex (not the twist), with a much smaller cross sectional area than the original part you've broken. It's why you'd need to be using higher strength bolts, but that's just making up for the strength you lose with less area...
×
×
  • Create New...