Jump to content
SAU Community

Recommended Posts

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

I dont think the bov has siezed. It's possible don't get me wrong but i feel it was never set up right in the first place. When you have the factory plumb back there is only the one hose running from the bov to the plenum. Yours is tee'd into with another hose running to the nipple under the cross over pipe. This is not the original setup and where that hose is supposed to go. There should be no 't' piece in the bov line. I will take a pic from my car and show you what i mean.

Thw way you will no for sure if its the bov of the way its hooked up is when you put your turbosmart one on and if it flutters through out the whole rev range - not working, hence its the vac line steup. If it goes pschhh then its all good and the hks bov was stuffed.

oh ok, because my car has been setup this way since i bought it, aparently the previous owner of the car said he had to disable it because he was defected for it, but a picture of your setup will definatly help me out as im thinking maybe it was a waste of time me buying a new bov, thinking my apexi wasnt working... if i can get this setup working maybe i wont need to change my setup...

Ok here are the pics of the correct setup you should have.

bovdiagram.jpg

You have the hose (with the red arrow pointing to it) tee'd into the bov hose (yellow hose). Where as on mine but hoses are seperate and run to the plenum.

bovdiagram2.jpg

You can see here the same hose and the points it attaches to (marked with blue arrows)

Yours appears to be tee'd into the bov hose for some reason becuase the hormal point that this hose (red arrow) connects to on the plenum appears to be used by another hose running toward the passenger side of the engine by near the fire wall. Where is that hose running to? Does it go through the fire wall and into the cabin? Maybe the guy beofr you used it to get a boost reading for the gauge...

Hope this helps :D

Hmm thats wierd so the bov only has the one hose now running to the plenum? In that case the bov must have stopped working, probably stuck or something as said above. Maybe you should just put on your turbosmart one on in its place and hopefully that one will work. You will probably need to buy an adapter though to it can flange on like mine.

yeah it comes with adaptor, just got to wait for it to come in the post hopefully this week... will it hurt to have a cross piece (X) instead of a T piece so i can have my boost gauge branching of it? or will it reduce accuracy of my boost gauge having to many lines?

You can just tee your boost gauge into the a hose at the front of the plenum. It a little hose only about 8 cm long at the front the the plenum towards the drivers side, and it wont interfere with the bov etc.

  • 2 weeks later...

hey guys i ended up putting my new bov on and set it up the same way that the pictures show (R33silverS2) and still has the flutter sound.... ;)

anyone know whats going?

could it be i should block off what looks like a bleed valve on my turbo (brass fitting on turbo, with hose comming of it leading to nowhere)...

pics...

took it for a drive and it flutters but when given a little bit it does both???

if i give it a good rev it goes off the way it should...

would it need adjusting???

and how? (as i dont have a manual)

Hey mate thats what its supposed to do. ;) Mine does the same and so would anyone elses with aftermarket bov. The bov only opens under higher load conditions such as more boost or higher revs etc. The rest of the time it remains closed and flutters. You can adjust when it opens by turning the head of the bov to make it tighter or looser. The looser you go the less flutter you will get as the more the bov will open and make sound etc. Your setup sounds right just loosen the bov a little.

Although when i say load i dont mean load as in forth gear cruising at 60 with you foot to the floor for a sec, more like when the revs can increase quite freely (lower gears for example)- if that makes sense.

Edited by R33silverS2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...