Jump to content
SAU Community

Recommended Posts

Hi all,

I need to get a roadworthy for my GTR32. Need one where they aren't picky on things cuz it's quite modified, but it has modification plates. It's just the stuff like it has no ABS, no aircon, etc etc. Basically I need a RWC no matter wot before this saturday!!! Inputs please!

Cheers~

Edited by J-Boy
Link to comment
https://www.sau.com.au/forums/topic/179885-need-rwc-for-modified-gtr/
Share on other sites

i got my car done at boike autmotive at kuraby, they didn't seem to worry too much about mods but they did look at the safety items, like steering, braking, drive train lights etc. no so worried about exhaust, suspension i.e. coilovers.

If he doesn't need the RWC, but would prefer one, and your going to get a dodgey one.. what is the point in getting one at all LOL

It's not that hard to get one though, just find a dodgey looking place and tell them you want to transfer the car from your dads name to yours asap, works a treat ;)

ACE auto in Murarrie did mine.

Although my car was fairly stock, they did not have anything to say about the following.

18" non standard wheels

Sports steering wheel

HKS blow off valve

Lowered

Eyelids over headlights

Cat back exhaust

They also looked after the car quite well, no grease or shit on the steering wheel or dirt in the carwhich is what you usually get after any mechanic has been in it.

There really are no "relaxed" places anymore, believe me I looked as I was really worried about the above.

They have all been shut down or will only do it for really really close mates.

Thanx guys, didn't need one in the end~ car's sold~

Even so, to clear up something for everyone.

Roadworthy does not depend on modifications done. There are certain guidlines that they must follow. Other than that, as long as the car is essentially safe, it should pass.

If you have a blue plate for your mods, then they should not even need to be checked in a roadworthy

Silly things pass like:

You can have absolutely no baffling left in your rear muffler but if it doesn't exceed noise limits and there are no holes then it passes.

No spare needs to be present.

Only driver's side window has to work

Oil leaks are ok as long as (after cleaned) they do not form one drip within 10 minutes.

Surface rust is ok but can't poke anything through it.

As you can see it's not like you have to have a new car to pass.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • also possibly backed up to my filler and shat down it! 🤣
    • Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
    • What sold me on Trailer Park Boys is this scene: Great stuff, just stay clear from the new Netflix production.
×
×
  • Create New...