Jump to content
SAU Community

Recommended Posts

Hi,

My headunit was replaced at the purchase of my car but i realised that my head unit does not have the auto antenna wire that pushes up the antenna when the head unit is on.

I do have the stock switch that lowers the antenna down and up but because its not connected to the head unit, it does not work.

Does anyone know where i can hook up the wire to?

just to clear things.

My headunit did not come with a auto antenna wire, where else can i hook it up to?

Thanks pplz!

Link to comment
https://www.sau.com.au/forums/topic/180019-antenna-switch/
Share on other sites

The standard switch should only change whether the mast is half-height or full height. The power-antenna wire on the headunit is used to fully retract the aerial when the tuner is not on (i.e. when you are playing a CD / auxillary input)

So if you don't have an power-antenna wire on your headunit, it should raise when you turn the ignition on, and retract when you switch off.

If you want to lower it fully, you'll have to wire up a manual switch off the factory loom. I guess you might be able to use the remote wire to trigger a relay, but all that would achieve is being able to retract the aerial when the headunit is not active (& in my car, the headunit is on probably 99% of the time the car is, which would make it kinda pointless in my opinion).

Link to comment
https://www.sau.com.au/forums/topic/180019-antenna-switch/#findComment-3276062
Share on other sites

yeah i want the half / full height option. i dont have that switch on my dash.

my aerial fully extends when tuner is selected on the head unit, and fully retracts when any other source is selected, or unit is off.

thats all good. but i want to only raise it half way when using the tuner.

Link to comment
https://www.sau.com.au/forums/topic/180019-antenna-switch/#findComment-3276146
Share on other sites

  • 3 weeks later...
The standard switch should only change whether the mast is half-height or full height. The power-antenna wire on the headunit is used to fully retract the aerial when the tuner is not on (i.e. when you are playing a CD / auxillary input)

So if you don't have an power-antenna wire on your headunit, it should raise when you turn the ignition on, and retract when you switch off.

If you want to lower it fully, you'll have to wire up a manual switch off the factory loom. I guess you might be able to use the remote wire to trigger a relay, but all that would achieve is being able to retract the aerial when the headunit is not active (& in my car, the headunit is on probably 99% of the time the car is, which would make it kinda pointless in my opinion).

Ive got a stacker in my 33 which only works through the radio frequency. I want to be able to lower the antenna when im using the stacker tho.

To acheive this can i just put a switch in to the remote wire so i can manually retract the aerial when the radio is on???

Link to comment
https://www.sau.com.au/forums/topic/180019-antenna-switch/#findComment-3321420
Share on other sites

Ive got a Xplod HU with mini disk player a jap edition.

And the answer is yes it works, I put a switch on the standard power antenna wire (green with red stripe) and done!!!

The antenna works as normal but i can over ride it when I'm listening to the stacker.

Nice!! :cheers:

Link to comment
https://www.sau.com.au/forums/topic/180019-antenna-switch/#findComment-3322669
Share on other sites

  • 1 month later...

I hooked mine up to the amp trigger wire (blue), it puts the arial up every time you turn on the head unit, but it still works. I am going to put a small switch in this to stop it being used all the time, maybe that will help

Link to comment
https://www.sau.com.au/forums/topic/180019-antenna-switch/#findComment-3432736
Share on other sites

haha u definately dont wanna do this haha they get the worst reception :rolleyes: mine barely works

I havn't had any problems with reception either, if anything I can pick up good reception with the antenna all the way down.

I'm very happy with the result, just need to replace with better looking switch and im done!

Link to comment
https://www.sau.com.au/forums/topic/180019-antenna-switch/#findComment-3432825
Share on other sites

I modded the factory switch wiring on a 33 aerial so it was either down or half up, never fully up. it was a girls car and the pioneer didnt put the aerial down when playing cds which annoyed her.

Also on r32s the aerial has a booster wire that needs power on it to get any reception it is a black wire with red trace. the main aerial in them is in the back window the one in the front is for am. Aerpro make a good aerial that has a wire you run through the car as the antenna i put them around the head lining. they get really good reception and are a good replacement if you dont want a external aerial

Edited by kiwi32
Link to comment
https://www.sau.com.au/forums/topic/180019-antenna-switch/#findComment-3437524
Share on other sites

  • 1 month later...
Ive got a Xplod HU with mini disk player a jap edition.

And the answer is yes it works, I put a switch on the standard power antenna wire (green with red stripe) and done!!!

The antenna works as normal but i can over ride it when I'm listening to the stacker.

Nice!! :D

Here's an idea, how about finding out the length of time it takes for antenna to raise and lower... then adding a timer to your switch? So everytime you click the switch it activates the timer, which then allows current to run for a set amount of time... like maybe 2 secs for half raised, or 4 secs for fully raised... Jaycar has DIY kits for timer...

Link to comment
https://www.sau.com.au/forums/topic/180019-antenna-switch/#findComment-3542611
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
    • OK, so a bunch of trim needs to come off to get to the rear shock top mounts. Once the seat is out of the way, the plastic trim needs to come off. Remove 2 clips at the top then slide the trim towards the centre of the car to clear the lower clip Next you need to be able to lift the parcel shelf, which means you need to remove the mid dark trim around the door, and then the upper light trim above the parcel shelf. The mid trim has a clip in the middle to remove first, then lift the lowest trim off the top of the mid trim (unclips). At the top there is a hidden clip on the inner side to release first by pulling inwards, then the main clip releases by pulling the top towards the front of the car. The door seal comes off with the trim, just put them aside. The the lighter upper trim, this is easy to break to top clips so take it carefully. There is a hidden clip towards the bottom and another in the middle to release first by pulling inwards. Once they are out, there are 3 clips along the rear windscreen side of the panel that are hard to get under. This is what the rear of the panel looks like to assist:
×
×
  • Create New...