Jump to content
SAU Community

Cooling Pro, Cooler Kits From Just Jap

BOOST ON

By BOOST ON,
in Engines & Forced Induction

 Share

Recommended Posts

BOOST ON Collaborator

BOOST ON

Posted
  • Author
Posted

very good, seems like its all thumbs, besides some people that are fussy. keeping in mind its for a 33 so all who have commented with a 33 your help has been good thanks! thanks for your pics to DMR.

cheers mick

MrMike Collaborator

MrMike

Posted
Posted

yeah dude go for it....i fitted one last weekend.......

few things to note.

*search for the instructions to fit a hybrid cooler. it has pretty much the exact location to cut the hole...i cut mine a cm or two further back so i wouldn't have to trim the fan.

* there is no nipple on the piping for the boost control.....i just tapped a thread in the piping and used some loctite...to seal it in there

* headlights were a bit of a shjt to get back in....had to modify a little bit.

* Angle grinder and jig saw are your best friends doing this job

Good luck man....if you need any advice throw me a pm as its still pretty fresh in my mind.

Mick

  • 2 months later...
  • 2 weeks later...
bombastic Collaborator

bombastic

Posted
Posted
I fitted one today actually!! Felt a huge difference.. Seems like turbo spools up a lot quicker :)

Haha... I felt no difference after putting on 34 SMIC. Didn't really feel a difference when I installed 3" turbo back either! Maybe I just need a tune.

What engine management you running now Sid?

frozenwaffles Mentor

frozenwaffles

Posted
Posted
you get what you pay for...... :D

thats true to a point but then if thats the case and a ferrari spyder is our benchmark (as would say a hks intercooler kit) then i guess what you are trying to say is we all drive peices of shit!

i dont htink so...its all about application and practicality. you wouldnt put a diamond incrusted turbo on your car would you now...'but it cost more so it must be better!' un no thats not the case.

anyway, for most people.. you will find the just jap intercooler kit more than adaquate!

s13_Skyline_inside Proficient

s13_Skyline_inside

Posted
Posted

ive fitted them to a few cars before, you do get what you pay for to a certain extent as far as the finish goes, some of the pipworks needs a bit of stuffing around to get the where its suppose to be which you wouldnt get that with a hks, arc etc kit but for the money you pay for them they are pretty good for a everyday street car with a bit of extra power, so as long as your not looking at huge amounts of power you really cant go wrong with them, so long as you dont mind some things ill fitting, just work around it :D

NVMYLH Apprentice

NVMYLH

Posted
Posted

anybody felt their car NOT going so well after puttin 1 of these kits on?? friend of mine recently put 1 on his 33 4 door, and he swears 1st/2nd gear do not pull as good as before, but 3rd/4th gear go like all hell! Had it dyno'd to check the afr's and its running well rich, and only made 165rwkw on 11psi! changed the plugs to bcpres 7's (i think it was, 7 heat range thats for sure) but it still does not go that well in 1st/2nd. Any ideas? He's has read somewhere that a SAFC might help a fair bit?

Blitz Grand Master

Blitz

Posted
Posted
anybody felt their car NOT going so well after puttin 1 of these kits on?? friend of mine recently put 1 on his 33 4 door, and he swears 1st/2nd gear do not pull as good as before, but 3rd/4th gear go like all hell! Had it dyno'd to check the afr's and its running well rich, and only made 165rwkw on 11psi! changed the plugs to bcpres 7's (i think it was, 7 heat range thats for sure) but it still does not go that well in 1st/2nd. Any ideas? He's has read somewhere that a SAFC might help a fair bit?

Sounds like your friend did not install it properly, or he has other issues which are causing the performance problems with his car.

Munkyb0y Grand Master

Munkyb0y

Posted
Posted
anybody felt their car NOT going so well after puttin 1 of these kits on?? friend of mine recently put 1 on his 33 4 door, and he swears 1st/2nd gear do not pull as good as before, but 3rd/4th gear go like all hell! Had it dyno'd to check the afr's and its running well rich, and only made 165rwkw on 11psi! changed the plugs to bcpres 7's (i think it was, 7 heat range thats for sure) but it still does not go that well in 1st/2nd. Any ideas? He's has read somewhere that a SAFC might help a fair bit?

he'd do alot better with engine management and a tune. safc should do the job

white33gtst Contributor

white33gtst

Posted
Posted

i just installed my JJR type 1 kit on my r33 in the last few days. bit of chopping here and there and abit of stress but it all worked out fine. took it for a run last night and i felt an improvement straight away. feels more torquey down low. definately a good buy. took a day and a half to fit it all up by myself

bombastic Collaborator

bombastic

Posted
Posted (edited)
to the dude that fitted a r34 smic and didnt feel much improvement, did you clean it out first? im not trying to stir, just curious.

Yes I first filled it with turps several times and shook it around, left it sitting awhile, then used metho to get rid of any residue.

Honestly I didn't expect any improvement and don't see why it would improve (well not noticeably anyhow). Except if you are boosting it for long enough that the stockie gets heat soak which I don't really do... The reason I got it was to be on the safe side.

Edited by bombastic
GTR 400 Enthusiast

GTR 400

Posted
Posted

I had a just jap 100mm tube and fin cooler for my R32 GTR and i pulled 335rwkw with it on. It is ok but doesnt seem to like the repeated dyno runs when she has been pushed.

It seems good to get to this power but i am changing to a Trust cooler only because i am changing turbos which will get me to 400R+rwkw ,and we felt this cooler was not flowing enough to go beyond this point, but hey for 300 odd dollars to get to this power is still great mind you i still have the standard rubber piping i just replaced the cooler only.

Also any one interested in a 2month old jjr tube and fin cooler i will be selling it cheap $250 still like brand new i live in Sydney.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      R32 GTS (RB20DE) Injectors Replacement

      By Duncan · Posted

      Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • GTSBoy
      Wheel Sizes & Offsets For Skylines

      By GTSBoy · Posted

      There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • GTSBoy
      Rear Sway Bar Busshings - Holden Astra TS (2002)

      By GTSBoy · Posted

      I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
    • GTSBoy
      R34 25GT Engine Light 21

      By GTSBoy · Posted

      Yeah - I mean, go the other way. Smaller range. Not larger.
×
×
  • Create New...