Jump to content
SAU Community

Recommended Posts

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

And dontcha just hate it when you walk out of the shop to find a nigga going through your car.

I was 5 yards from my car inside a small local butcher shop and when i stepped out the door heres a coon tryin to make off with my sunny's, smokes and loose change. Then the prick had the nerve to threaten me. WTF!, I hit the bastard hard as i could Hard headed prick he was and he dropped the shit and ran. Farkin punk :domokun::domokun:

What did ya bitch slap him :domokun: , come on Noel i thought you could hit harder than that :laugh: , the plan is to drop them as well as ur stuff.

At least you got gear back thats the main thing. :)

What did ya bitch slap him :domokun: , come on Noel i thought you could hit harder than that :laugh: , the plan is to drop them as well as ur stuff.

At least you got gear back thats the main thing. :)

Sub i slammed the punk. his head went back and belted the door pillar like you wouldnt believe. I expected him to melt on the footpath but as quick as a rat he darted out from under me and bolted. I bet he's feelin it now tho. :domokun:

What really pissed me off was the thievin prick was taking my stuff then threatened me, Like WTF. Thats when i lost it and belted the turd.

Sub i slammed the f**ker. his head went back and belted the door pillar like you wouldnt believe. I expected him to melt on the footpath but as quick as a rat he darted out from under me and bolted. I bet he's feelin it now tho. :laugh:

What really pissed me off was the thievin prick was taking my stuff then threatened me, Like WTF. Thats when i lost it and belted the bastard.

Fock yeah that would piss ya off with him turning around and threatening you.

You will be glad to know that.

Edited by subzeroR33
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...