Jump to content
SAU Community

Recommended Posts

na i got to sell my car first plus i found a few alot cheaper if i import it my self i can hav a gtr v spec in in alice complied and every thing with only 29 000 km 4 just over 45 000

  • 2 weeks later...

Geez the Darwin forums have been going well the last few weeks, thought I'd post a Alice drag update.

Ben was quickest qualifier in Super Street and ran a few 11.0 runs, came so close to cracking a 10.

I ran 3 11.8 runs on the final day and I definately have reached the limits of my skinny 235, bald street tyres. My new Mickey Thompson's turned up in time but my rims didn't. So I will have to wait till the next meeting on the 21st to try them out.

In Street class I think Chris got a low 13 and Steve a 15.

It was great to see all the interstate guys come to the meet. Lots of impressive cars and team setups.

...word. More Power! Not enough corners to worry about in Alice.

BK has laptop & Power FC software now and might look at other cars.

For suspension a Hicas lockbar, strut brace or front swaybar may do the trick. Some bushes can be hard to fit.

Me personally, I would fit skinny tyres to stock rims on the rear and enjoy :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...