Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...

Hey guys I have a question. I am keen to have my ecu rechipped, with nistune

but I also have a ecutalk v2 display, I was wondering if the 2 were

compatible and if my ecutalk display would still work after having nistune installed.

I have done several searches on google and various forums and I have been unable to find any info. :laugh:

any help would go a long way thanks.

Link to comment
https://www.sau.com.au/forums/topic/181930-nistune/page/11/#findComment-5170133
Share on other sites

hey ppl, might be a silly question but does nistune use an afm?? eg, if wanting to upgrade to a z32afm, is it needed or not??

cheers

If someone was to make a map sensor replacement module for the nistune/stock ecu would there be much interest in something like this?

It can certainly be built but if theres no interest I won't bother researching it.

Link to comment
https://www.sau.com.au/forums/topic/181930-nistune/page/11/#findComment-5170937
Share on other sites

already looked into this. Should be very simple, read in map sensor values read in air temp sensor add correction factor output 0 - 5v signal back to the ecu. Main thing would be the need for a complete retune of entire map, but this effort could be minimized with extensive logging of afm and map values in parallel(Similar to the holden MAFless tunes). I believe some one has also used TPS as loading on an NA Vl commodore using nistune

Edited by Crans
Link to comment
https://www.sau.com.au/forums/topic/181930-nistune/page/11/#findComment-5170950
Share on other sites

Yep if you did no correction and just made sure it was linear in the range used from 0-5v it would still be very easy to tune.

Ah so many ideas and so little time. Need to get my car running and buy a decent oscilloscope so I can finish the VCT controller I've been carrying on about.

Link to comment
https://www.sau.com.au/forums/topic/181930-nistune/page/11/#findComment-5171022
Share on other sites

Hey guys I have a question. I am keen to have my ecu rechipped, with nistune

but I also have a ecutalk v2 display, I was wondering if the 2 were

compatible and if my ecutalk display would still work after having nistune installed.

I have done several searches on google and various forums and I have been unable to find any info. :P

any help would go a long way thanks.

I can confirm my ecutalk v2 display (and 1.3.x windows software) work fine in my nistune'd R32 GTR. love the new 2.02 firmware with the user-configurable alarms and am gagging for the eventual logging to micro-sd.

Link to comment
https://www.sau.com.au/forums/topic/181930-nistune/page/11/#findComment-5173040
Share on other sites

hey guys i just bought a r32 gts4 and was thinking of doing the nistune upgrade for the ecu, but i want to change it to a manual as well. would i need to get a manual ecu or a gtr ecu? or would it be fine once the daughterboard is installed? don't wanna upgrade then find out i need a new ecu lol.

Link to comment
https://www.sau.com.au/forums/topic/181930-nistune/page/11/#findComment-5175332
Share on other sites

the daughterboard can be reprogrammed for different ROM images. bascially we can put a manual program in auto ECU no problems

GTR ECU is completely different you wont be needing that in a GTS-4 unless doing an RB26 transplant with twin AFMs

Link to comment
https://www.sau.com.au/forums/topic/181930-nistune/page/11/#findComment-5176244
Share on other sites

Are the daughterboards for 32GTSt and 32GTR the same?

Reason I am asking is I am looking at Nistuning my 32gtst but if I max out my z32 afm, I am wondering if I can swap the daughterboard in to a 32GTR ECU and get a GTR image loaded on there ? (and then run a GTR engine harness and twin afm's)

Link to comment
https://www.sau.com.au/forums/topic/181930-nistune/page/11/#findComment-5176335
Share on other sites

Wanting to buy a board and tunning package to have a play with.

Any one else using it? What do you think f it?

How do you buy it? Ive sent emails no one answers

I bought and installed my Nistune daughterboard direct from the guys that make it.

It is installed in my S13, and was tuned by Mark @ MRC dyno in castle hill. I haven't had any issues with it, and for the price i think it is an excellent option.

Link to comment
https://www.sau.com.au/forums/topic/181930-nistune/page/11/#findComment-5176539
Share on other sites

got a question for ya's

i have a type 4 daughter board in my r34.

I know that the daughter board has its own EEPROM that we can change the values in while tuning in nistune software. And the original ECU's EEPROM stays unchanged, we just tell the ECU to read from our new EEPROM. Is this correct?

If this is correct, could i tune my car on pump fuel 98, then take the hex file from the daughter board's EEPROM and burn it into the original ECU's EEPROM, then re-tune the daughter board as usual on e85 fuel? then i just have to run a couple of switch wires from the jumper pins on the original ECU to the dash and i have instant capability to drive on either fuel.

But is it even possible to burn a new image into the original ECU?

and can anyone see any major flaws in my idea?

Link to comment
https://www.sau.com.au/forums/topic/181930-nistune/page/11/#findComment-5176589
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Seems like a decent result for a modded JZX110. They are bulky in comparison to the 100 and 90 models (which I'd prefer myself) but they are getting very few and far between here in JP these days. Thanks for the detailed review and the import process into the UK. I also have a car which I'm hoping to export from Japan at some stage so it's good to know if someone from the UK was interested in it. By the way the corrosion underneath is par for the course for cars which were located in/near the mountains or along the Japan sea coastline. They get huge amounts of snow every winter and the sodium chloride is used on the roads. Many cars have some kind of rubber like treatment underneath but they tend to limit it to the wheel arches underbody and fuel tank. Suspension arms and sub-frames will have similar corrosion to your JZX110 which is a common sight. See it all the time and car dealers here generally don't even mention it unless asked.
    • If the sound goes away when you clutch in, the 1.5/2 way diffs are just shit, and you are a normal person. The diff is likely "fine" but driving at anything under 30kmh is a violent horrible experience. It would be exaggerated with solid diff bushings and subframe bushings if you have those.
    • Trailer got new mudguards to accommodate the new wheels Lightweight ally Painted, stickered and done ✅ 👌  
    • Did you hit up the search function? R33 and greddy and cable returns this thread with some options.   https://www.sau.com.au/forums/topic/358214-rb25-throttle-body/
    • Thanks buddy.. the standard one needs to be about another inch or inch and a half longer. Thanks anyway
×
×
  • Create New...