Jump to content
SAU Community

Recommended Posts

hey guys

selling these:

BODY:

r32 2dr drivers door-$100

r32 REAR reo bar -$50

r32 type-m rear bar -$100

bar.jpg

DRIVELINE:

r32 gtr/gts4 driveshaft -$150

adadadsa2.jpg

SUSPENSION & BRAKES:

r32 type-m rear calipers-$140 with rotors

full set of r32 GTST M-spec rotors-80

r32 rear 5 stud hubs with LCA-$250

r32 koni rear 2 point height adjustible shocks gts4/gtr-$200

rear r32 2dr handbrake lines-$100

wae24ed3.jpgp10retret.jpg

LIGHTS

r32 type-m fog lights (pair)-$50 bucks

wqe213ads2213.jpg

interior parts:

r32 2dr rear trim under 1/4 window -$80 both for lhs+rhs

-LHS=$50

-RHS=$50

rear view mirror-20

r32 1993 spec rear seats velour-$100

steering wheel-$40 clear defects/cheap stocko wheel (just checked it out now from awhile ago not 100% condition. peeling at the top. no wire for horn)

r32 interior goodies- mostly perfect condition ~take wat u need~ - make an offer

p1010048.jpgp1010045.jpg rearseats2.jpg

let me no

express your interest :pwned:

all item located in melb eastside dandenong

call/msg=0413820421 ( if i dont pik up just msg)

email/[email protected]

post-24514-1199463441_thumb.jpg

post-24514-1199463457_thumb.jpg

post-24514-1199463497_thumb.jpg

Edited by Dan_J

abu : nah sorry no air box

Kwyjibo : silver with blue pearl (factory colour) , i have pics up its just the fact that the imagethrust.com server went down

G'day,

You got Steering wheel? What condition is it in?

Do you have plastic cover @ A pillar? If so, how much?

When are you free for me to come and have a look at it (not tonight) maybe tomorrow?

PM me.

Cheers

Grant

  • 1 month later...
  • 2 months later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...