Jump to content
SAU Community

Recommended Posts

Gday,

On my r33 gtst I've worn my right front inside shoulder down bare. I'm guessing I've got too much neg camber on this front wheel. Left front is heading down the same path.

How is the camber adjusted on an r33, is it adjustable without buying an aftermarket camber pin kit? Or is this more to do with alignment? The car itself tracks straight, hence i'm guessing camber problems.

Link to comment
https://www.sau.com.au/forums/topic/18315-front-tyre-wear/
Share on other sites

I like the standard camber angle and would leave it alone. if you adjust it for best tyre wear the car will handle like sh1t. Just take the tyres off and swap them over so they wear on the other side. my falken's wore badly like this. i've had bridgestone s03's now for about 10,000km and havent flipped the fronts yet and they dont even look like wearing unevenly.

Link to comment
https://www.sau.com.au/forums/topic/18315-front-tyre-wear/#findComment-382516
Share on other sites

I dont know about rotating for better wear. A lot of performance tyres are directional. I'd recommend the camber adjustment kit or an extension on the standard adjustment. Whether it will handle like shit or not depends if you are racing. For street, I can tell you it makes no difference to handling....how do I know?....cos I had all four of my wheels camber adjusted back in for wear reasons. Go to a reputable suspension mob for quality advice RB25 my good man!

Link to comment
https://www.sau.com.au/forums/topic/18315-front-tyre-wear/#findComment-382537
Share on other sites

you can still swap side with directional tyres, you just need to have them rotated on the rim at the same time (so they point the other way).

And i'd check both camber and toe-in, it can probably be adjusted within the factory adjustment without needing a kit.

Link to comment
https://www.sau.com.au/forums/topic/18315-front-tyre-wear/#findComment-382564
Share on other sites

guys - in my post i said to take the tyres off the rims. so what you do is leave the rims on the car and swap tyres keeping them pointed in the proper direction. this will wear them on the other side. trust me - i do it all the time.

and no - you cant rotate directional tyres. i do this coz i have 235 on the front and 275 on the back....

Link to comment
https://www.sau.com.au/forums/topic/18315-front-tyre-wear/#findComment-382659
Share on other sites

Originally posted by rb25

guys - in my post i said to take the tyres off the rims. so what you do is leave the rims on the car and swap tyres keeping them pointed in the proper direction. this will wear them on the other side. trust me - i do it all the time.

i was telling my mate to do this just yesterday

i didnt think some one would think this was as well

just goes 2 show that great minds think alike :D

Link to comment
https://www.sau.com.au/forums/topic/18315-front-tyre-wear/#findComment-382715
Share on other sites

RB25.....fair cop, I agree you could swap the tyres. But I think the best would be to sort the prob out once and for all ?? Each to his own....I just couldn't be stuffed rooting around every couple of months swapping tyres. My tyres were wearing out on the inner side down to bald at around 6-8 months. That would mean, after swapping, I would still only get 12-16 months out of a set of fronts...maybe a tad longer on the rear. Now I have the problem sorted, I've seen diddly squat wear on front or back....no stuffin around...no change in handling.

Just my experience.

cheers Ozzy

Link to comment
https://www.sau.com.au/forums/topic/18315-front-tyre-wear/#findComment-382779
Share on other sites

Not enough negative camber. Same as my car, got kmac strut tops and still cant get enough. Grrrrr.

If you have your car set up for good front end grip under spirited driving with some decent negative camber, it will wear the inside edge if you just drive around sedately.

Link to comment
https://www.sau.com.au/forums/topic/18315-front-tyre-wear/#findComment-385029
Share on other sites

Originally posted by rb25

350z's wrx's and hsv's are common victims :) I love to chop blokes in their R8's. they think theyre unbeatble in thier heaps of sh1t. i like to sh1t stir em at the next set of lights --  whats wrong with you car mate? why cant your big v8 beat my jap crap 2.5litre 6?   I dont even bother racing these morons anymore - i just rev the skyrine @ the lights, let em drop the clutch and then i putter off like nanna.

let the whoring end.....

hahahahahhaaa I LOVE IT!!!!

hahaha!!! I am not alone :)

Link to comment
https://www.sau.com.au/forums/topic/18315-front-tyre-wear/#findComment-396355
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...