Jump to content
SAU Community

Recommended Posts

Sup all,

Have a small problem perhaps you all can help me with??? I have a sticker baked on my car's duco, does anyone know of a way to remove it easily and without removing the paintwork with it?? all advice is appreciated ... :)

post-35468-1188732331_thumb.jpg

post-35468-1188732344_thumb.jpg

Edited by immortal^

explain baked on? as in it was a normal sticker which was put on the duco and then through heat from the sun is stuck on?

if thats the case, use a hair dryer to heat the sticker up and make it plyable. then using a rag, rub hard and break the sticker up, then using a cutting paste, cut and polish the area to remove the sticky residue.

Yeah pretty much as you said cheez... normal sticker gone hard over time due to nature.

Thanks cheez, ive heard that before I will try it, needed someone to reafirm my ideas, cool.

get a hair dryer.... heat over the sticker for a couple of minutes... then buy yourself a bottle of Eucoliptous oil (hope I spent it right) and with a small tower... start to crub it off slowly - it will come off!!

Like they said use some heat, but I prefer to use a toffee wheel to remove the glue, its a rubber wheel that fixes to a drill, use it on a slow high torque setting and it takes it off with out using sometimes dangerous chemicals, really really good product!!

Your find them on ebay:

http://cgi.ebay.ie/Eraser-Toffee-Wheel-Pad...oQQcmdZViewItem

Edited by DriftyR33

step 1,,,,,,,,borrow a heat gun, apply heat, not to close, then start to peel with your nail, if you know any panel beaters,painters or house painters, they will have one, or buy cheap one from bunnings,

step 2,,,,,,use a wax and grease remover to remove the glue thats left on panel,

step 3,,,,,,polish, as will be a shade diffrence around where sticker was,

step 4,,,,go into panel shop, get them to do it, a sat morning best and slip them 10 bucks, only takes 5 mins to do if you have correct tools

then buy yourself a bottle of Eucoliptous oil (hope I spent it right) and with a small tower... start to crub it off slowly

thats some shithouse english right there....

seriously though, ive used a razorblade to do it many times and it works a treat. i know it sounds dodgy but if u have half a clue as to what you are doing you will easily be able to take off the adhesive without scratching the crap out of your paint

that sucks. i used to be a detailer for about 4 years. the way we used to do it is with a heat gun then peel it off in sections. use a bit of preptone or prepsol. then cut and polish it. if its baked on, trust me when i say your always gonna see where the sticker was on your duco

good luck

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok guys thank you very much. GCG highflow it is then 🙂 
    • forgot to mention that when it does this it does not kill the engine, but I have not kept the pedal down long enough to let it, as I see no reason to beat up on it as its got to be something simple, small and dumb causing this.  And as soon as I let off pedal, the engine returns to its normal super smooth operation and rpms re-stabilize quickly, once below 4k. 
    • neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
×
×
  • Create New...