Jump to content
SAU Community

Recommended Posts

Hey all just wondering if any gtst(32 or 33) wheels would fit on an r32 gtr. I am going up to Winton at the end of the month and I don't really want to be burning up my brand new 265 pirellis or ruin my 18 x 10'' Leon Hardiritt deep dishes, brag brag brag,haha.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/183569-gtst-rims-on-gtr/
Share on other sites

You should put equal width front and rear tyres so that you don't stuff up the attessa/4wd system?

Nah, just pull out the fuse and rip skids :P

Yeah, they fit, i couldnt put down power in 2nd, 3rd and 4th on some roads which was fun but in the rain its just frustrating - have a look;

Fronts

Hotrims003.jpg

Rears i cant find a pic of, but yeah, the gap between the rims and the guards is just embarassing

Where about is the fuse for the 4wd system?

hey guys im new to this site. as i have only had my gtr for 4 months now......

lol i seem to have alot of fun pulling out the fuse.. but at times it just gets to to to dangerous especially in the wet even with 18x10 on the back, the amount of traction i loose is quite fun.

anyways

the fuse u pull out on the top left hand corner on the fuse box that is just about your right knee whilst driving.

when u pull is out u will see the 4WD light appear as well as the ABS..... this is normal.

cheers

  • 1 year later...

lol, spend all ur money on rims for the street then put crappy stockies on for track. people will never cease to amaze me :P

if u want to spend some time on the track spend some $$ on some decent wheels for the track. that or just harden up and use the wheels uve got on now, a lot of drifters slide on much more expensive wheels than the ones u are talking about.

no point bothering with stockies, u wont have f**k all grip, and the tyre will just flop around.

You should put equal width front and rear tyres so that you don't stuff up the attessa/4wd system?

nah, as long as the overall diametre is kept constant from front to rear ull be fine, width has nothing to do with it.

the fuse box is located above your right knee whilst sitting in the drivers seat.

so on the right bottom side of the steering wheel.

Yep there is a fuse in there you can pull as well

Or

When driving turn the car off then back on (while still rolling) HICAS light will come on and the car will be in RWD mode. If the car stops moving, so you stop at lights etc the AWD with activate again

That's another way to get it into RWD mode

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
    • The BES920 is like the Toyota Camrys of coffee machines. E61 group head is cool, however the time requirements for home use makes it less desirable. The Toyota Camry coffee machine runs twin boilers and also PID temp control, some say it produces coffees as good as an E61 group head machine.
    • And yes with a full tank it will hit limiter free revving or driving 6B6CDF6E-4094-426D-A9CB-6C553475FE36.mp4
×
×
  • Create New...