Jump to content
SAU Community

Recommended Posts

I snapped these images of my front and rear suspension. These were fitted before my R33 arrived from Japan.

FRONT

REAR

The rear says NISMO on the spring, but can't see it on front. These are coilovers right? I thought they are but i need a second opinion, and if someone knows anything about this model too.

Also can you tell if they are adjustable? The ride is very firm and bumps around a lot on uneven roads. It's great on smooth, high speed corners though. It's also been lowered a little.

Any advice is great. Cheers ;)

Link to comment
https://www.sau.com.au/forums/topic/184492-are-these-coilovers/
Share on other sites

Yes, all Skylines use coilover suspension from factory.

To see if they are adjustable, look for little knobs either at the bottom of the shock, or in your engine bay at the strut tops.

Edited by Yawn
yawn: skylines dont use coilovers from factory?

Yes, they do. A "coilover" is a suspension setup where the coil sits "over" (or, more accurately, around) the strut. Whether they're adjustable or not is irrelevant.

The V35 Skylines don't use a coilover arrangement in the rear, as the strut and spring are separated.

I'll jack up the car with the wheel off and take a looksy. I don't know what 'adjustable' looks like though, i'll take another pic?

I wanted to get my suspension adjusted anyways cause the ride is too firm for Sydney roads. Any advice on who to go see about that and relative costs?

sounds to me like you need your spring rates looked at.

or if you really want to be able to adjust your dampening and rebound then yes your going to have to go for a set of fully adjustable coil overs.

I'll jack up the car with the wheel off and take a looksy. I don't know what 'adjustable' looks like though, i'll take another pic?

I wanted to get my suspension adjusted anyways cause the ride is too firm for Sydney roads. Any advice on who to go see about that and relative costs?

If I remember the marketing guff correctly, they said that its to provide better geometry or something.

All I know is that I do get plenty of rear end grip in my Z33 (which shares the same platform), and its a right pain in the arse to adjust my ride height in the rear because you need to adjust the strut's mounting point as well as the cradle for the spring.

Not the spring rate (not likely). I would suspect the shocks are "dead". A nice set of Bilsteins, or even KYBs, would solve your ride problems.

I doubt they're dead. When there's people in the back the rear doesn't bounce around much. The ride is more comfortable and the shocks dampen bumps more. I want the suspension to absorb bumps all the time though! :)

drop your wheel and take some better pics of it. also check from the top of the strut if there's any notches etc where you can adjust the dampening.

nismo sells stiffer aftermarket springs to sit on stock struts too, so could just be stock struts with springs.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Can u check this way it works for power supply?
    • These coils draw 10amps that what i read online
    • I appreciate the detailed explanation, think I understand now. I spent the better part of last night reading what I could about shuffle and potential solutions. I had replaced the OEM twin turbo pipe with an alternate Y pipe that is separated further away from the turbo. The current one is from HKS and I had a previous pipe that was separated even further away, both have shuffle. I had heard that a divider can be welded in to the OEM pipe to remove turbulence, and figure that aftermarket pipes that are more separated would achieve the same thing. From what I read, most people with -10 turbos get shuffle due to their size, though it's a bit less common with -5s on a standard RB26. I think Nismoid mentioned somewhere it's because OEM recirculation piping is common in Australia with -5 cars. It seems that the recommendation tends to vary between a few options, which I've ordered in what I think is most feasible for me:  1. Retune the MAP or boost controller to try to eliminate shuffle 2. Install OEM recirculation piping 3. Something called a 'balance pipe' welded onto the exhaust manifolds. I don't know if kits for this are available, seems like pure fabrication work 4. simply go single turbo My current layout is as follows: Garrett 2860 -5s HKS Racing Suction intake MAF delete pipes HKS racing chamber intake piping hard intercooler piping,  ARC intercooler HKS SSQV BOV and pipe Haltech 2500 elite ECU and boost solenoid/controller HPI dump pipes OEM exhaust manifolds HKS VCAM step 1 and supporting head modifications Built 2.6 bottom end All OEM recirculation piping was removed, relevant areas sealed off I'll keep an eye out for any alternative solutions but can get started with this.  Only other question is, does shuffle harm the turbo (or anything else)? It seems like some people say your turbo shafts will explode because of the opposing forces after a while and others say they just live with it and adjust their pedal foot accordingly. 
    • That worked out PERFECTLY! Thank you big time to JJ. He was able to swap me his stock diff. He drove all the way to me as well. Killer! Removal & install was pretty straightforward. The diff itself is HEAVY. So that’s a 2 man job.  Man does the car drive nice now! Couldn’t have worked out any better 👌
×
×
  • Create New...