Jump to content
SAU Community

I'm Calling The Sau Prez Out!


Recommended Posts

  • Replies 58
  • Created
  • Last Reply

Top Posters In This Topic

lol why not go to Captian Americas and do their burger challange

a burger weighing 1kilo and 600grams of chips :P

now thats a challange

OK guys, can I get a show of hands who's up for this? I'll organize a night down there for us, anyone welcome.

I'll post a thread and sort it if there is enough interest :(

Depending on the date (always away for work :P )I'll be in on this. I'd love to have a crack at Captain America. I see the world record is an inasane 8 min! If I do it in 20 I'd be wrapped!

Is anyone on here a known guts/eating machine?

It would be good to have someone be our bench mark! hahaha :D

By the powers vested in me as President of SAU-Vic, how should I say this.....??

IT'S ON LIKE DONKEY KONG!!

Now, all we have to do is find a venue and time to have said SAU Vs WRX burger challenge.

Let's all understand though that the challenge will be to eat one of Age's original burger thingos with the donuts, not some Maccas, Hungry Jacks or Captain Americas burger.

I can't wait to see this on YouTube!

Ppppft, I'd kill ages burger in about 5 mins if that, that Captain America's burger, that's a world of pain, my chest if hurting thinking about it now....no really!

Hey Adz, have you finished the Captain America meal before? If so what time did you do it in?

If we do Age's burger is it a timed event or do we get points just for finishing? :D

OK guys, can I get a show of hands who's up for this? I'll organize a night down there for us, anyone welcome.

I'll post a thread and sort it if there is enough interest :P

would deff be in for that hahaha

might give the challange ago lol

last time i did it it took me and 2 mates to finish it all and we still had a little fries left over

so im in for that. only 10 mins from my house :D

If we do ages, I reckon it's timed. The Captain America's one is a killer, dunno what the time was, Milkshake didn't help the cause though :)

Hahaha...I'd do either as long as their is no Milkshakes or hot sauces involved...Just a pure eating comp :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...