Jump to content
SAU Community

Recommended Posts

Yeah, replacing it from manual to auto is a good idea if you want to cruise it... Auto is only like 5 kws weaker anyways... people make it out to be heaps but actually not a huge difference.

i have had a fair bit of work done by nissco in bayswater... my motor was built there, had some shit fabricated, been very happy. 9571 4743 speak to Randy, Say Ryan with the blue 16/silver stagea sent ya

-Ryan

If your talking about Auto to Manual then RE Customs did it for me. Ring them up for a quote.

But speaking from experience. Don't do it. Cheaper/Better to sell and buy a manual. THe main cost being R33 Box goes for about $1500

Dont need to replace the computer. Don't need to relpace the diff.

I still have my auto diff (meant to be better for launches? I can't compare) but the first 2 gears are very short.

Yeah, replacing it from manual to auto is a good idea if you want to cruise it... Auto is only like 5 kws weaker anyways... people make it out to be heaps but actually not a huge difference.

That would be a huge waste. Not even worth spending the money. May as well swap someone with an auto if you don't care about the money, at least your not spending money.

im such a knob cant believe i wrote that backwards it is meant to be auto to manual hahaha guess i wasnt awake yet lol.im not selling and swapping i love the car too much and rare colour green blue two tone over grey..love it.thanks for all the help tho

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...