Jump to content
SAU Community

Recommended Posts

yeah i'm gonna be having a bbq, i don't care about the weather

it'll most likely be hot anywayz :P

i might have moved by my birthday, or at least will be trying to find a place, so i dont really know what ill be doing.

im bored also, watching MPU.

What kind of power can set of GTR rods handle?

Hopefully at least 350awkW. I say this because I have left standard R32 GTR conrods in my engine rebuild on advise from Peter Hall (formally from Willall Racing). However, I did purchase Tomei conrod bolts & CP forged pistons and the conrods were all tested prior to putting the engine back together.

but can a rb20 pull same power as rb26/30 :P ?

So yeh...how much for rb30e rebuild ???

Of coarse it can, but it will be super laggy.

Rb30e rebuild; 7-7.3k rev limit ~2.5k.

rb30e 8.5k revlimit ~5k.

Darren has pushed his stock rb30rods to 470rwkw with a 7k rev limit. :P

Of coarse it can, but it will be super laggy.

Rb30e rebuild; 7-7.3k rev limit ~2.5k.

rb30e 8.5k revlimit ~5k.

Darren has pushed his stock rb30rods to 470rwkw with a 7k rev limit. :P

Thats why im keeping my rb30e bottom end stock :P cant wait till my rb25/30 is all done might put it in a sleeper vl with hub caps and a I LOVE JESUS sticker

Thats why im keeping my rb30e bottom end stock :rofl: cant wait till my rb25/30 is all done might put it in a sleeper vl with hub caps and a I LOVE JESUS sticker

So u just going to leave the block as it it (and im assuming it came out of a 250k+km car...)...????

Of coarse it can, but it will be super laggy.

Rb30e rebuild; 7-7.3k rev limit ~2.5k.

rb30e 8.5k revlimit ~5k.

Darren has pushed his stock rb30rods to 470rwkw with a 7k rev limit. :rofl:

A workshop offered me a rebuilt rb30 bottom end (standard rebuild) for 1k...and its an expensive workshop... Am i missing something ?

check this for a LOL

http://www.prostreetromania.ro/prostreet.htm

nfi if its a repost...

that was so funny

Yeh that is quite a funny website......... BUT DAYUM I want in on some of that Romanian beauty!!

just for Darren Romanian Beauties

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...