Jump to content
SAU Community

Recommended Posts

mates 180 is written off because of some stupid f**king wog parking in a no standing zone and 1m from the curb and because the 2 cars in front hit the breaks

not too happy

your mate was too close to stop = fail

A rear ender like that is usually open and shut, 100%, tailenders fault.

Hope your all OK and no-one was hurt.

your mate was too close to stop = fail

A rear ender like that is usually open and shut, 100%, tailenders fault.

Hope your all OK and no-one was hurt.

i think ive busted my shoulder up , gonna go get it checked out tomorrow

my mates devastated cause he just got the car with a loan and now it seems to be written off

sure its not my car but im on the verge of tears cause it brought back memories from a major car accident i was in a few years back :P

your mate was too close to stop = fail

A rear ender like that is usually open and shut, 100%, tailenders fault.

Hope your all OK and no-one was hurt.

+1

hope u guise are all ok

i dont really trust anyone on the roads, fkt if i sit any closer than 3 car lengths behind ppl. been a passenger in similar situation, with a mate who is a hero that can drive close to ppl

thanks

+1

hope u guise are all ok

i dont really trust anyone on the roads, fkt if i sit any closer than 3 car lengths behind ppl. been a passenger in similar situation, with a mate who is a hero that can drive close to ppl

i sit atleast 4 cars away from the car in front , we just came off the lights and then it happened :)

looks like me n my mate will be turning it into a sil80 now :P

thanks

i sit atleast 4 cars away from the car in front , we just came off the lights and then it happened :)

looks like me n my mate will be turning it into a sil80 now :P

yeah, i just consider everyone else on the road is a tard.

hope ur aches n pains arent too bad when u wake up in the morning.

on the plus side...... u guise have a new project :)

yeah, i just consider everyone else on the road is a tard.

hope ur aches n pains arent too bad when u wake up in the morning.

on the plus side...... u guise have a new project :)

we had a project before we went to get kfc

replace the Y fork in his transmission :D

got the part on hold at nisswreck but im guessing we will be haulin s13 parts around now :)

were also going to order coilovers , bucket seat , sway bars , strut braces , caster rods and brake cylinder stoppers for both of our cars but im sure thats on hold now :(

oh well , life goes on , cars are repairable

end of the day , too many tards on the road :P

yeah sure. whenever i need to take them off again or free one weekend i'll let u know.

btw kye they look tough. Just need those coilovers now.

Edited by Luke_ENR34
yeah sure. whenever i need to take them off again or free one weekend i'll let u know.

btw kye they look tough. Just need those coilovers now.

haha yeah tell me about it. its pretty dumped but just needs another inch or so to set it right off.

ill be bottoming out on small pebbles by the time i get it low enough :P

abit mexican at the front though! going to run smaller tyers and more camber i think

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
    • When you pulled it off, there is no signs of blown head gasket? Is it possible you have some other issues going on? Possible cracked blocked? Or do you think it's straight up lifting the head? Did you check what the head was torqued to before pulling it down (To see if possibly they're stretching, or starting to break threads out etc)?
    • Seems like a decent result for a modded JZX110. They are bulky in comparison to the 100 and 90 models (which I'd prefer myself) but they are getting very few and far between here in JP these days. Thanks for the detailed review and the import process into the UK. I also have a car which I'm hoping to export from Japan at some stage so it's good to know if someone from the UK was interested in it. By the way the corrosion underneath is par for the course for cars which were located in/near the mountains or along the Japan sea coastline. They get huge amounts of snow every winter and the sodium chloride is used on the roads. Many cars have some kind of rubber like treatment underneath but they tend to limit it to the wheel arches underbody and fuel tank. Suspension arms and sub-frames will have similar corrosion to your JZX110 which is a common sight. See it all the time and car dealers here generally don't even mention it unless asked.
    • If the sound goes away when you clutch in, the 1.5/2 way diffs are just shit, and you are a normal person. The diff is likely "fine" but driving at anything under 30kmh is a violent horrible experience. It would be exaggerated with solid diff bushings and subframe bushings if you have those.
×
×
  • Create New...