Jump to content
SAU Community

The Sa Wasteland

Cubes

By Cubes,
in South Australia

 Share

Recommended Posts

Madaz Grand Master

Madaz

Posted
Posted

yeah when my first core went i bought the whole box from the wreckers and Luke and I pulled my whole dash out using the guide on here but i had the core go another 2 times so all up broke 3 cores

when my 2nd core broke i took it too synergy because i doubted my work and i wanted the insurance of if it broke again they would have to pay for it because they sourced the core also, then that core broke and i took it back for warranty work and few other things like blender motor as well

  • Replies 36k
  • Created
  • Last Reply

Top Posters In This Topic

  • Damo_R34

    2820

  • scandyflick

    2266

  • Madaz

    1919

  • craig R33

    1717

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Ryanrb25
Ryanrb25

i went for a hills run last night in the 31 with the roads very slippery.....was much fun. Had to bed in the bottom end bearings so yea..took it for a strap.

DSTROY
DSTROY

Hey Ryan, do you know how to fit a set of drop spindles to the front of a hilux???

Madaz
Madaz

Dam straight Damo would rather do SAU them heroin gts4 are 4.1 because they share the same parts from the gtr i think r32 gtst is 4.3 because of the lack of torque from the rb20

Posted Images

Dohmar Grand Master

Dohmar

Posted
Posted
Cool, thanks... I feel a little better about it now :(

if you get stuck, gimmie a call cause I've done this before on the 32. Having the dash out makes it easier but u can do it without the glovebox like steve said (just means its a little tricky to unclip the actuator from its mount.

If its anything like mine, it'll just be dry solder joints (like the guide steve posted a while back shows). Hope you're handy with a soldering Iron...

-D

TALBO Grand Master

TALBO

Posted
Posted
if you get stuck, gimmie a call cause I've done this before on the 32. Having the dash out makes it easier but u can do it without the glovebox like steve said (just means its a little tricky to unclip the actuator from its mount.

If its anything like mine, it'll just be dry solder joints (like the guide steve posted a while back shows). Hope you're handy with a soldering Iron...

-D

Thanks, I'm going to wait a couple of weeks until I complete the house move then have a go at it..... Yeah I'm pretty bloody good with the soldering iron now after about 8 channels of mic preamp, around 4 compressor/limiters and a couple of EQ's and then many many PSU's...LOL!

Inline 6 Grand Master

Inline 6

Posted
Posted (edited)

anyone know any chick bike riders?? a friends gota pink bike for sale for 4k its a 250cc or whatever the L plater limit is. Think its a suzuki but can find out if anyone knows someone after a pink bike

all minto, she hardly ever used it and everything got rebuilt when she bought it. she wasted her money good if you ask me :P

Edited by Inline 6
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...