Jump to content
SAU Community

The Sa Wasteland

Cubes

By Cubes,
in South Australia

 Share

Recommended Posts

Krishy Grand Master

Krishy

Posted
Posted
How do I engine flush? Ive never done it and oils due in 1500 (5K intervals) Guessing its just a additive to pour in and wait till it drains out? Im running castrol edge sport 5w30 in the stag and seems ok. Ive seen people ranting of this Fuchs stuff in the stag section and its pretty cheap apparantly asked repco about it and they said id be going backwards...?

Should i do the oil before the dyno even though its not going be due for another week or 2?

To do an engine flush you buy an additive and put it in with your current oil. Let the car idle for about 10 mins, then dump the oil while its still warm. Easy as!

If your going from synth to mineral you have to change your oil filter too. (I do it every service anyway)

If anyone is interested in trying ULX 110 then let me know, the distributor works with me so could probably get discount.....

I would suggest that you use Penny's advice but instead of puting the additive with your current oil, get some fully synthetic 0W20 oil which you should never drive on and then change oil, add additive and then let the car warm up to operating temperatures and then drain that oil. Change the oil filter to a new one and chuck in some Motul 8100 or anything of your choice....If i am correct thats how you flush your engine :)

  • Replies 36k
  • Created
  • Last Reply

Top Posters In This Topic

  • Damo_R34

    2820

  • scandyflick

    2266

  • Madaz

    1919

  • craig R33

    1717

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Ryanrb25
Ryanrb25

i went for a hills run last night in the 31 with the roads very slippery.....was much fun. Had to bed in the bottom end bearings so yea..took it for a strap.

DSTROY
DSTROY

Hey Ryan, do you know how to fit a set of drop spindles to the front of a hilux???

Madaz
Madaz

Dam straight Damo would rather do SAU them heroin gts4 are 4.1 because they share the same parts from the gtr i think r32 gtst is 4.3 because of the lack of torque from the rb20

Posted Images

scandyflick Grand Master

scandyflick

Posted
Posted (edited)

well, got a fine in the mail today. i ran an amber, 2 cops say i ran a red. my word vs. theirs. guess who wins. looks like ill be driving like an old lady 10km/h under the limit in the right hand lane (like basically everyone else in sa) til my licence recovers.

Edited by scandyflick
ontheranch Experienced

ontheranch

Posted
Posted
I am not saying that your method is wrong Penny

Just a different approach to doing it i guess and its a bit more expensive but i reackon it does a better job

No worries, just though you were correcting me. Haha

Unless you have done heaps of KMs or run it on shit oil then a flush isn't crazy important because you shouldn't have big sludge build up, different story for older engines.

I only had to do it because of the Synth to Mineral change. I was also told I could change the oil with a cheap mineral first (no additive), run it, drain it and then put in the good stuff. That's more expensive tho..

DSTROY Grand Master

DSTROY

Posted
Posted (edited)

I dont know why most of you guys waste so much money on oil just to drive around on the street :) I use Castrol Edge 0w-40 in the Skyline and run it at 18psi (420rwhp) foot flat lap after lap at Mallala and the engine loves it and it only cost about $70 from Super Cheap.

Only thing i do is change the oil before every track day.

Edited by DSTROY
TALBO Grand Master

TALBO

Posted
Posted

I just drained 7.5K Km old Motul 8100 and it looked relatively good other than it's dark appearance, no sludge. Just replaced filter and put in some 10/40 300V chrono, didn't do a flush as I don't think it's necessary... yet :)

Chad I used 300V this time because I'm not going to change it again until it's clocked up 10K Kms.

Dave I know how you feel, I got done running an amber and got screwed in court because the officers affidavit didn't make the situation look good for me..... but we've been over all this previously hey Pete :)

kidafa Veteran

kidafa

Posted
Posted

yeah im not going to flush as i dont see the point im just curious of how its done...

I change mine every 5K relegiously and even did a 2.5k swap when i first got it to make sure it was all real fresh. Always do filter too.

oil and filters cost me Fall I get trade at repco

Import S13 Veteran

Import S13

Posted
Posted

Got a message from a mate that there is going to be 60 cops coming over from Victoria (great swine flu) this thursday for a 2 week blitz in Adelaide.

Donno what the blitz is on but I'm guessing it's going to be everything. Just a warning :)

scandyflick Grand Master

scandyflick

Posted
Posted

yeah, read something along similar lines on 31club. dude who started the thread thinks its a defect blitz. probably bullshit, but it couldnt hurt to be a little more careful with that many more unmarkeds potentially* on the road.

*its probably bullshit.

180or200 Proficient

180or200

Posted
Posted
anyone got a hex socket that goes onto a wrench to remove head studs i could borrow

gotta take the head off a ca18det

and gotta find out what size it is

anyone know ?

cheers

I just got one from sprints for my rb25 head bolts, was 10mm, cost around $15 i think!

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      NC MX5

      By Dose Pipe Sutututu · Posted

      Lamb roast on Saturday will be different 🥲
    • TurboTapin
      RB25DET with solid lifters - which cams ?

      By TurboTapin · Posted

      They are under bucket shims. Tomei provides a test shim kit and then any measurement of shim required. 
    • GTSBoy
      RB25DET with solid lifters - which cams ?

      By GTSBoy · Posted

      I always wondered how you were supposed to buy a set of 24 buckets and somehow magically have every single one of them yield exactly the desired clearance. I would have thought you'd need to assemble a cam with either 12 "sample" or "example" buckets of known top thickness (or a single such sample/example 12 times over!!) measure clearances at every valve, and then do the usual math to work out what the actual "shimness" of each bucket needed to be, before buying the required buckets to make up he thicknesses that you didn't have on hand.
    • TurboTapin
      RB25DET with solid lifters - which cams ?

      By TurboTapin · Posted

      I now seem to be limited in power due to my rev limit/hydraulic lifters in my built RB25. I'm looking into converting over to Tomei solid lifters. Question for anyone that has done the conversion. I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  I don't know where I got this idea, as so far I see no mention of this in any of the Tomei documentation. It just states I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      I couldn't agree more. I should have started from the get-go with a NEO or solid bucket conversion. I started looking into converting over to solid lifters yesterday. Now for some reason I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  But I see no mention of this on any of the Tomei documentation. It just states that I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
×
×
  • Create New...