Jump to content
SAU Community

Recommended Posts

How do I engine flush? Ive never done it and oils due in 1500 (5K intervals) Guessing its just a additive to pour in and wait till it drains out? Im running castrol edge sport 5w30 in the stag and seems ok. Ive seen people ranting of this Fuchs stuff in the stag section and its pretty cheap apparantly asked repco about it and they said id be going backwards...?

Should i do the oil before the dyno even though its not going be due for another week or 2?

To do an engine flush you buy an additive and put it in with your current oil. Let the car idle for about 10 mins, then dump the oil while its still warm. Easy as!

If your going from synth to mineral you have to change your oil filter too. (I do it every service anyway)

If anyone is interested in trying ULX 110 then let me know, the distributor works with me so could probably get discount.....

I would suggest that you use Penny's advice but instead of puting the additive with your current oil, get some fully synthetic 0W20 oil which you should never drive on and then change oil, add additive and then let the car warm up to operating temperatures and then drain that oil. Change the oil filter to a new one and chuck in some Motul 8100 or anything of your choice....If i am correct thats how you flush your engine :)

well, got a fine in the mail today. i ran an amber, 2 cops say i ran a red. my word vs. theirs. guess who wins. looks like ill be driving like an old lady 10km/h under the limit in the right hand lane (like basically everyone else in sa) til my licence recovers.

Edited by scandyflick
I am not saying that your method is wrong Penny

Just a different approach to doing it i guess and its a bit more expensive but i reackon it does a better job

No worries, just though you were correcting me. Haha

Unless you have done heaps of KMs or run it on shit oil then a flush isn't crazy important because you shouldn't have big sludge build up, different story for older engines.

I only had to do it because of the Synth to Mineral change. I was also told I could change the oil with a cheap mineral first (no additive), run it, drain it and then put in the good stuff. That's more expensive tho..

I dont know why most of you guys waste so much money on oil just to drive around on the street :) I use Castrol Edge 0w-40 in the Skyline and run it at 18psi (420rwhp) foot flat lap after lap at Mallala and the engine loves it and it only cost about $70 from Super Cheap.

Only thing i do is change the oil before every track day.

Edited by DSTROY

I just drained 7.5K Km old Motul 8100 and it looked relatively good other than it's dark appearance, no sludge. Just replaced filter and put in some 10/40 300V chrono, didn't do a flush as I don't think it's necessary... yet :)

Chad I used 300V this time because I'm not going to change it again until it's clocked up 10K Kms.

Dave I know how you feel, I got done running an amber and got screwed in court because the officers affidavit didn't make the situation look good for me..... but we've been over all this previously hey Pete :)

yeah im not going to flush as i dont see the point im just curious of how its done...

I change mine every 5K relegiously and even did a 2.5k swap when i first got it to make sure it was all real fresh. Always do filter too.

oil and filters cost me Fall I get trade at repco

Got a message from a mate that there is going to be 60 cops coming over from Victoria (great swine flu) this thursday for a 2 week blitz in Adelaide.

Donno what the blitz is on but I'm guessing it's going to be everything. Just a warning :)

yeah, read something along similar lines on 31club. dude who started the thread thinks its a defect blitz. probably bullshit, but it couldnt hurt to be a little more careful with that many more unmarkeds potentially* on the road.

*its probably bullshit.

anyone got a hex socket that goes onto a wrench to remove head studs i could borrow

gotta take the head off a ca18det

and gotta find out what size it is

anyone know ?

cheers

I just got one from sprints for my rb25 head bolts, was 10mm, cost around $15 i think!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Put a fuel pressure gauge on it. Replace the turbos. Probably completely separate issues.
    • What copper washer do you guys use on the bleeder bolts? The existing one I have I had no idea where to find it in a local store, I did buy some online but that are only 1mm thick whereas my old one is 2mm+ thick and when I put the new washer out and squeeze the top radiator hose I can hear a bit of air but not with the old one. Does this matter? The new one doesn't leak, but the inner diameter is a bit loose whereas the old one threads on the bolt.
    • Howdy all, after being out a few weeks ago on a spirited drive in my GTR I have 2 issues that oddly have appeared at the same time. Whilst accelerating quickly through the gears all of a sudden i’ve lost power at the top of third gear (below redline around 6000rpm) for no obvious reason.    From that point onwards the car has been running rich on idle, won’t really rev under load without a ton of black smoke and the odd backfire, and dying as a pull up to a set of lights unless I keep the revs up around 1500rpm. In addition when shutting down the car that same night (I was 10 minutes from home) I noticed one of the turbos was significantly noisy on wind down when shutting off the engine. After letting the car cool down overnight it starts up fine, although once it gets to temp the revs start to creep up and down, the exhaust is darker than it should be and it also sounds like it’s running rich (fat note) I’ve put a new set of plugs in it - no change, the old plugs all seemed OK with two of them being somewhat richer/fueled up than the other 3 with 1 being borderline. I’ve smoked tested the intake system via the front of the Turbos, found a split vacuum hose going to the factory boost gauge sender, which I have since replaced.  Also found another leak on the gasket coming off the rear turbo outlet, have also replaced this. After fixing both of these leaks - still have the running rich issue. I’ve also tried another pair of AFM’s - no change here After pulling off the front turbo intake pipes, there is obvious shaft play in the front turbo, which now hisses loudly on light revvs although I can’t see why this would make the car run funny even under idle. I’m curious to know why it’s running rich before I potentially replace/rebuild turbos. The car is completely stock <50,000kms  other than an exhaust. Oil and coolant are all clear. I haven’t bothered with coil packs as it looks like they won’t be the issue due to condition of the plugs. Any help appreciated as I cry myself to sleep!
    • No probs at all. I used to love trying to dig up obscure info for those in need where possible going back 20+ years on SAU.  I did have another look and couldn't come up with any closer match. I'm leaning towards those skirts in your first pic are custom fitments, cut down/extended or from another car entirely and modded to fit an R34 sedan. I would've thought someone in Japan had them and taken a photo at some stage over the last 2 decades but there's nothing. Someone out there must know surely.
×
×
  • Create New...