Jump to content
SAU Community

Recommended Posts

That is bad timing - just today I bit the bullet and decided I will sell all the R34 gear I had accumulated, but not yet fitted to my 34. Including a set of Super Spark coilpacks with 3 spares.

Dang! oh well, i got JJR ones, 1 year warranty, for $417 delivered. What else you got laying around? Air con facia by any chance? :blink:

Had a blackout last night at work (irrigation piping factory) so from 3am - 6am we did nothing and then when the power came back on - we Just cleaned because by the time the power had retuned the machines had cooled down :blink:

AWESOMEEE!

guess you wont like my plans for the works then.

:P

ps:

4090.jpg

colour coded hi-spec lips are gay. i want those foglights, those corner markers, and the clear fronts.

also so very glad i got the s14 skirts instead of the s14a skirts.

Edited by scandyflick

has anyone had to appeal their probationary licence before for no p plates ?

everyone ive spoken to says the court doesnt give a shit that i need my licence for work and that i will cop 6 months disqualification

is this so ? :D

has anyone had to appeal their probationary licence before for no p plates ?

everyone ive spoken to says the court doesnt give a shit that i need my licence for work and that i will cop 6 months disqualification

is this so ? :D

depends if its a mandatory loss of licence. nothing u can do when its mandatory (such as the case if you're over 0.05 - automatic 6 months regardless)...

Get a lawyer, they can talk traffic offences down. Give Matthew Mitchell Solicitors a call at 8344 5589 and tell them what you're facing.

-D

i got caught with no p plates.

its a minor frigging thing !

reckon i have a chance of getting off ?

edit// i got done for speeding last october and i learnt my lesson from that , and then i got caught with no p plates in my dads work car.

NO NO NO

i havent appealed before , ive only had my licence just over 12 months.

got done for speeding in october , copped that & now its p plates

ive had a couple of tickets in between now and then but nothing with demerit points attatched (fail to maintain vehicle standards & written warning for disoby stop sign)

Life Story entry #322

Drew from AAA fitted a resonator to the 33 today. Sounds much better. The car is now totally cop-friendly.

While it was up on the hoist, took a peak under the body. The car is clean as. No leaks except for some weeping at the steering rack for the power steering hoses. A quick clean and torquing and I'll check it out again in 5,000kms. Otherwise, no leaks at all, and everything in top condition. All CV boots are top nick.

/waits for keyboard warriors to say oh its your fault you broke the law

Waiting ...

Best bet dude is to get legal advice.

Pretty much depends on the magistrate on the day, and what else prosecution comes up with. If the magistrate can see it as a simply mistake, and he's having a good day, you might be lucky. Go with Dohmars suggestion, get a lawyer or solicitor, grab some character references off past employers or the like and see how you go. Best of luck with it though, it does just sound like a simple mistake though.

Edited by Jamesrb25
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
    • Hi, i’m converted my r34 4dr auto to manual but need help with gearbox wiring. There are bunch of wires no idea which one for speedo drive, neutral, reverse can anyone help me. IMG_6860.mov
×
×
  • Create New...