Jump to content
SAU Community

Recommended Posts

yeah i have a HKS cooler but no piping for it as it was custom shit from my gtr motor , im getting a oil cooler eventually aswell

just need to get out there sliding asap !

Rush into it and you'll have another blown motor

Signed up another bunch of members tonight. New membership cards are coming to all SAU:SA members.

And a heads up ... get in quick because the next two membership numbers are #0033 and #0034 :D

(#0035 is already taken ... I had my arm twisted by "he who waves the ban stick")

Signed up another bunch of members tonight. New membership cards are coming to all SAU:SA members.

And a heads up ... get in quick because the next two membership numbers are #0033 and #0034 :D

(#0035 is already taken ... I had my arm twisted by "he who waves the ban stick")

Hmmmmmm, do i want #0033...how much is membership?

Hmmmmmm, do i want #0033...how much is membership?

Membership is $30 per year + $15 once off admin charge = $45 (plus +$5 for associate member card for partner).

:D

nah for the 34, gonna shove that on for a grip session when i get everything sorted. 31 would need a bit of work to be track ready, and since im keeping the 34, gonna have a few fun laps in it :D

be a pal, you can buy some coilovers for the 33 while youre there. :D

I wish! Don't know whether to go for a FMIC first or suspension. All too hard cause I don't want to cut reo and cop a defect either!!!

I got to go speak to a suspension expert about lowering my car because I definitely don't want a harsh ride, being a daily driver. If I can get it 25-30mm lower with spring rates very similar to what they are now and of course correct camber I'll be happy.... don't really think it needs to be any lower than that.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...